REMOVAL
Removal / installation · Vehicles built Jun 2006 – Sep 2006
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| 1.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
|
| 2.
REMOVE FRONT DOOR SCUFF PLATE LH
|
 |
- Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.
| 3.
REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
|
 |
- Remove the cowl side trim clip.
Disengage the 2 clips and remove the cowl side trim sub-assembly LH.
| 4.
REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
|
 |
- Remove the bolt <A> and the screw <B>.
Disengage the 2 claws and the DLC3.
Disconnect the hood lock control cable assembly.
Disengage the claw and the 4 clips.
Remove the air hose, disconnect the connector, and then remove the lower No. 1 instrument panel finish panel.
| 5.
REMOVE LOWER INSTRUMENT PANEL FINISH PANEL
|
 |
- Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.
| 6.
REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY |
 |
- Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.
| 7.
REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH
|
 |
- Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.
| 8.
REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH
|
 |
- Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.
| 9.
REMOVE POSITION INDICATOR HOUSING ASSEMBLY |
 |
- HINT:
- for LHD: (Click here).
- for RHD: (Click here).
| 10.
REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY |
 |
- HINT:
- for LHD: (Click here)
- for RHD: (Click here)
| 11.
REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY
|
 |
- Remove the 2 screws <F>.
Disengage the 4 claws.
Disconnect each connector and remove the instrument cluster finish panel center sub-assembly.
- HINT:
- Set the shift lever in the D position.
| 12.
REMOVE CONSOLE BOX POCKET
|
 |
Remove the console box pocket.
| 13.
REMOVE CONSOLE BOX CARPET
|
 |
- Remove the console box carpet.
| 14.
REMOVE CONSOLE BOX ASSEMBLY
|
 |
- Remove the 2 screws <F>.
- Disengage the clamp.
Remove the 2 bolts <G> and the console box assembly.
| 15.
REMOVE NO. 2 CONSOLE BOX INSERT FRONT
|
 |
- Remove the 3 screws <F>.
Disengage the clip and remove the No. 2 console box insert front.
| 16.
REMOVE NO. 1 CONSOLE BOX INSERT FRONT
|
 |
- Remove the 3 screws <F>.
Disengage the clip and remove the No. 1 console box insert front.
| 17.
REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY |
 |
Disconnect the end of the transmission control cable assembly from the shift lever assembly.
- Disconnect the transmission control cable assembly from the shift lever assembly.
| 18.
REMOVE SHIFT LEVER ASSEMBLY |
 |
- Disconnect the shift lock control ECU connector and transmission control switch wire connector.
- Remove the 4 bolts and shift lever assembly.