INSTALLATION
Removal / installation · Vehicles built from Jun 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
| 1.
INSTALL FRONT POWER SEAT LUMBAR SWITCH (for Manual Seat) |
 |
- Install the front power seat lumbar switch with the 2 screws.
| 2.
INSTALL FRONT POWER SEAT LUMBAR SWITCH (for Power Seat) |
 |
- Install the front power seat lumbar switch with the 2 screws.
| 3.
INSTALL FRONT SEAT CUSHION SHIELD (for Manual Seat)
|
 |
Connect the connector. (w/ lumber support)
- Engage the 2 claws.
Install the front seat cushion shield with the 2 screws.
- Install the 2 rubber bands on the backside of the front seatback board sub-assembly.
| 4.
INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY (for Power Seat)
|
 |
- Connect the connector.
Engage the 2 claws.
Install the front seat cushion shield assembly with the 5 screws.
- Install the 2 rubber bands on the backside of the front seatback board sub-assembly.
| 5.
INSTALL RECLINING ADJUSTER RELEASE HANDLE (for Manual Seat)
|
 |
- Engage the claw to install the reclining adjuster release handle.
| 6.
INSTALL VERTICAL ADJUSTING HANDLE (for Manual Seat)
|
 |
- Install the No. 2 vertical adjusting handle with the 2 screws.
| 7.
INSTALL VERTICAL ADJUSTER COVER LH (for Manual Seat)
|
 |
- Engage the 2 claws to install the vertical adjuster cover.
| 8.
INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB (for Power Seat)
|
 |
- Install the slide and vertical power seat switch knob.
| 9.
INSTALL RECLINING POWER SEAT SWITCH KNOB (for Power Seat)
|
 |
- Install the reclining power seat switch knob.
| 10.
INSTALL FRONT SEAT ASSEMBLY (for Manual Seat)
|
 |
Place the front seat assembly in the vehicle and align the adjuster pin with the hole on the vehicle side.
Connect the connector and clamp.
Move the front seat assembly to the rearmost position by operating the slide handle.
- NOTICE:
- Check that the seat is locked.
- Temporarily install the front seat track bracket with the 2 bolts.
Move the front seat assembly fully forward by operating the slide handle.
- NOTICE:
- Check that the seat is locked.
- Temporarily install the rear seat track bracket with the 2 bolts.
Move the front seat assembly to the rearmost position by operating the slide handle.
- NOTICE:
- Check that the seat is locked.
Fully tighten the 2 bolts on the front seat track bracket in the order of the inner side bolt and then the outer side bolt.
-
Torque:
- 37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
Move the front seat assembly fully forward by operating the slide handle.
- NOTICE:
- Check that the seat is locked.
Fully tighten the 2 bolts on the rear seat track bracket in the order of the inner side bolt and then the outer side bolt.
-
Torque:
- 37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
| 11.
INSTALL FRONT SEAT ASSEMBLY (for Power Seat)
|
 |
Place the seat in the cabin.
Connect the connectors under the seat.
Connect the cable to the negative (-) battery terminal.
Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.
- Temporarily install the front side of the front seat assembly with the 2 bolts.
Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.
- Temporarily install the rear side of the front seat assembly with the 2 bolts.
Move the front seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.
Fully tighten the 2 bolts on the front side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.
-
Torque:
- 37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
Move the front seat assembly fully forward by operating the slide and vertical power seat switch knob.
Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of the inner side bolt and then the outer side bolt.
-
Torque:
- 37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
| 12.
INSTALL INNER SEAT TRACK BRACKET COVER (for Manual Seat)
|
 |
- Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.
Push the inner seat track bracket cover inner to engage claw B.
| 13.
INSTALL INNER SEAT TRACK BRACKET COVER (for Power Seat)
|
 |
- Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.
Push the inner seat track bracket cover to engage claw B.
| 14.
INSTALL OUTER SEAT TRACK BRACKET COVER (for Manual Seat)
|
 |
- Slide the outer seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.
Push the outer seat track bracket cover to engage claw B.
| 15.
INSTALL OUTER SEAT TRACK BRACKET COVER (for Power Seat)
|
 |
- Slide the outer seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.
Push the seat track cover to engage claw B.
| 16.
INSTALL FRONT SEAT HEADREST ASSEMBLY |
|
| 17.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Manual Seat) |
|
| 18.
INSPECT SLIDE ADJUSTER LOCK (for Manual Seat) |
|
| 19.
INSPECT SRS WARNING LIGHT (w/ Airbag System) |
 |
Inspect the SRS warning light. (Click here)
| 20.
INSPECT FRONT SEAT ASSEMBLY (for Power Seat)
|
 |
Inspect the power seat operation.