2006-2011 Camry Aurion · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. REMOVE FRONT SEAT HEADREST ASSEMBLY

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for Manual Seat)

NOTICE:
Wait for 90 seconds after disconnecting the cable to prevent the airbag from deploying (Click here)


3. REMOVE OUTER SEAT TRACK BRACKET COVER (for Manual Seat)
  1. Move the front seat assembly fully forward by operating the slide handle.

  1. B149587
    Using a screwdriver, disengage the 4 claws and remove the outer seat track bracket cover.

    HINT:
    Tape the screwdriver tip before use.


4. REMOVE OUTER SEAT TRACK BRACKET COVER (for Power Seat)
  1. Operate the power seat switch knob and move the seat to the position farthest forward.

  1. B149587
    Using a screwdriver, detach the 4 claws and remove the outer seat track bracket cover.

    HINT:
    Tape the screwdriver tip before use.


5. REMOVE INNER SEAT TRACK BRACKET COVER (for Manual Seat)

  1. B149588
    Using a screwdriver, disengage the 4 claws and remove the inner seat track bracket cover.

    HINT:
    Tape the screwdriver tip before use.


6. REMOVE INNER SEAT TRACK BRACKET COVER (for Power Seat)

  1. B149588
    Using a screwdriver, detach the 4 claws and remove the inner seat track bracket cover.


7. REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)
  1. Move the front seat assembly to the rearmost position by operating the slide handle.

  1. B139101
    Remove the 2 bolts on the front seat track bracket.

  1. Move the front seat assembly fully forward by operating the slide handle.

  1. B139102
    Remove the 2 bolts on the rear seat track bracket.

  1. Move the front seat assembly to the center position and adjust the seatback to the vertical position by operating the slide and reclining adjuster release handle.

  1. Disconnect the connectors and clamp.

  1. Remove the front seat assembly.


8. REMOVE FRONT SEAT ASSEMBLY (for Power Seat)
  1. Operate the power seat switch knob and move the seat to the rearmost position.

  1. B149590
    Remove the 2 bolts on the front seat track bracket.

  1. Operate the power seat switch knob and move the seat to the position farthest forward.

  1. B139102
    Remove the 2 bolts on the rear seat track bracket.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent the airbag and seat belt pretensioner from deploying (Click here).

  1. Disconnect the connectors under the seat. Then remove the front seat assembly.


9. REMOVE VERTICAL ADJUSTER COVER LH (for Manual Seat)

  1. B139103
    Using a screwdriver, disengage the 2 claws and remove the vertical adjuster cover LH.

    HINT:
    Tape the screwdriver tip before use.


10. REMOVE VERTICAL ADJUSTING HANDLE (for Manual Seat)

  1. B139104
    Remove the 2 screws and vertical adjusting handle.


11. REMOVE RECLINING ADJUSTER RELEASE HANDLE (for Manual Seat)

  1. B139105
    Lift the reclining adjuster release handle.

  1. Using a screwdriver, disengage the claw and remove the reclining adjuster release handle.

    HINT:
    Tape the screwdriver tip before use.


12. REMOVE RECLINING POWER SEAT SWITCH KNOB (for Power Seat)

  1. B149584
    Using a screwdriver, detach the reclining power seat switch knob.

    HINT:
    Tape the screwdriver tip before use.


13. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB (for Power Seat)

  1. B149585
    Using a screwdriver, detach the slide and vertical power seat switch knob.

    HINT:
    Tape the screwdriver tip before use.


14. REMOVE FRONT SEAT CUSHION SHIELD (for Manual Seat)

  1. B153813
    Disengage the 2 hooks.

  1. B149580
    Remove the 2 screws.

  1. Disengage the 2 claws and separate the front seat cushion shield.

  1. Disconnect the connector from the front power seat lumbar switch. (w/ lumber support)


15. REMOVE FRONT SEAT CUSHION SHIELD ASSEMBLY (for Power Seat)

  1. B146651
    Disconnect the 2 hooks.

  1. B149573
    Remove the 5 screws.

  1. Disengage the 2 claws and separate the front seat cushion shield assembly.

  1. Disconnect the connector from the front power seat lumbar switch.


16. REMOVE FRONT POWER SEAT LUMBAR SWITCH (for Manual Seat)

  1. B178400
    Remove the 2 screws and front power seat lumbar switch.


17. REMOVE FRONT POWER SEAT LUMBAR SWITCH (for Power Seat)

  1. B146654
    Remove the 2 screws and front power seat lumbar switch.

← REMOVAL (Oct 2006 – May 2009)INSPECTION (from Jun 2006) →