Using a screwdriver, disengage the 4 claws and remove the front seat rear inner track bracket cover.
HINT:
Tape the screwdriver tip before use.
7.
REMOVE FRONT SEAT ASSEMBLY (for LHD)
Operate the power seat switch knob and move the seat to the rearmost position.
Remove the 2 bolts on the front seat track bracket.
Operate the power seat switch knob and move the seat to the position farthest forward.
Remove the 2 bolts on the rear seat track bracket.
Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent the airbag and seat belt pretensioner from deploying (Click here).
Disconnect the connectors under the seat. Then remove the front seat assembly.
8.
REMOVE FRONT SEAT ASSEMBLY (for RHD)
Operate the power seat switch knob and move the seat to the rearmost position.
Remove the 2 bolts on the front seat track bracket.
Operate the power seat switch knob and move the seat to the position farthest forward.
Remove the 2 bolts on the rear seat track bracket.
Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent the airbag and seat belt pretensioner from deploying (Click here).
Disconnect the connectors under the seat. Then remove the front seat assembly.
9.
REMOVE RECLINING POWER SEAT SWITCH KNOB (for LHD)
Using a screwdriver, detach the reclining power seat switch knob.
HINT:
Tape the screwdriver tip before use.
10.
REMOVE RECLINING POWER SEAT SWITCH KNOB (for RHD)
Using a screwdriver, detach the reclining power seat switch knob.
HINT:
Tape the screwdriver tip before use.
11.
REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB (for LHD)
Using a screwdriver, detach the slide and vertical power seat switch knob.
HINT:
Tape the screwdriver tip before use.
12.
REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB (for RHD)
Using a screwdriver, detach the slide and vertical power seat switch knob.
HINT:
Tape the screwdriver tip before use.
13.
REMOVE FRONT SEAT CUSHION SHIELD ASSEMBLY (for LHD)
Disconnect the 2 hooks.
Remove the 5 screws.
Disengage the 2 claws and separate the front seat cushion assembly.
Disconnect the connector from the front power seat lumbar switch.
14.
REMOVE FRONT SEAT CUSHION SHIELD ASSEMBLY (for RHD)
Disengage the 2 hooks.
Remove the 5 screws.
Disengage the 2 claws and separate the front seat cushion shield assembly.
Disconnect the connector from the front power seat lumbar switch.
15.
REMOVE FRONT INNER SEAT CUSHION SHIELD (for LHD)
Remove the screw.
Disengage the 3 claws and remove the front inner seat cushion shield.
16.
REMOVE FRONT INNER SEAT CUSHION SHIELD (for RHD)
Remove the screw.
Disengage the 3 claws and remove the front inner seat cushion shield.
17.
REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY (for LHD)
Remove the 2 screws.
Disconnect the 14 clamps and front separate type seatback cover.
Pull the seatback board in the direction indicated by the arrow in the illustration to detach the 2 claws. Then, remove the seatback board.
18.
REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY (for RHD)
for Except Sports Seat Type:
Remove the 2 screws.
Disengage the 4 claws and front seatback board sub-assembly.
for Sports Seat Type:
Remove the 2 screws.
Disconnect the 14 clamps and front separate type seatback cover.
Pull the seatback board in the direction indicated by the arrow in the illustration to detach the 2 claws. Then, remove the front seatback board subassembly.
19.
REMOVE FRONT SEAT HEADREST SUPPORT (for LHD)
Detach the 2 claws and remove the headrest support.
HINT:
Use the same procedure for the RH side and LH side.
20.
REMOVE FRONT SEAT HEADREST SUPPORT (for RHD)
Disengage the 2 claws and remove the front seat headrest support.
HINT:
Use the same procedure for the RH side and LH side.
21.
REMOVE FRONT SEATBACK ASSEMBLY (for LHD)
w/o Airbag System:
Remove the 2 hog rings and 3 hooks.
Remove the front separate type seatback assembly.
w/ Airbag System:
Remove the 2 hog rings and 3 hooks.
Remove the nut and 2 seatback cover brackets.
Remove the front seatback assembly.
22.
REMOVE FRONT SEATBACK ASSEMBLY (for RHD)
for Except Sports Seat Type:
Remove the 3 hog rings.
Remove the 5 hog rings.
Disengage the 6 hooks.
Remove the nut and separate the 2 brackets.
Remove the front seatback assembly.
for Sports Seat Type:
Disengage the 3 hooks.
Remove the 2 hog rings.
Remove the nut and separate the 2 brackets.
Remove the front seatback assembly.
23.
REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY (for LHD)
Disconnect the connector.
Remove the 2 screws and lumbar support adjuster.
24.
REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY (for RHD)