2006-2011 Camry Aurion · Service Manual SECURITIES

SYSTEM DESCRIPTION

Troubleshooting · Vehicles built Jun 2006 – May 2009

Versions by build date: Jun 2006 – May 2009 from Jun 2009


OUTLINE OF THEFT DETERRENT SYSTEM
  1. The theft deterrent system can be set by locking the doors using the transmitter, or by opening and closing the doors.
  2. The alarm function will activate when someone attempts forcibly to unlock any of the doors or open any of the doors, engine hood, and luggage door while the system is in the armed state.
  3. In the alarm sounding state, the system illuminates the interior light and blinks the taillight, headlight, and hazard warning lights. At the same time, the system sounds the vehicle horn and security horn to deter break-in and theft as well as to warn the people around the vehicle.
  4. The theft deterrent system has the active arming mode. There are 4 states; a disarmed state, an arming preparation state, an armed state, and an alarm sounding state.
  1. Disarmed state:

    1. The alarm function is not operating.
    2. The theft deterrent system is not operating.

  2. Arming preparation state:

    1. The time until the system goes into the armed state.
    2. The theft deterrent system is not operating.

  3. Armed state:

    1. The theft deterrent system is operating.

  4. Alarm sounding state:

    1. The alarm function is operating.

    Alarm time:
    Approx. 30 sec.

    Refer to table below for alarm method and time: 

    Hazard Warning Light
    Blinking
    Interior Light
    Illuminating
    Vehicle Horn
    Sounding
    (approx. 0.4 second cycles)
    Security Horn
    Sounding
    (approx. 0.4 second cycles)
    Alarm Time
    Approx. 30 sec.

    HINT:
    If any of the doors are unlocked when the key is not in the key cylinder during the armed state, a forced door lock signal will be output (see FORCED DOOR LOCK CONTROL).


FUNCTION OF MAIN COMPONENTS
Component
Function
Security indicator
Informs driver of theft deterrent system status.
Security horn
Sounds when attempted brake-in or theft is detected.
Hazard warning lights
Blinking when attempted break-in or theft is detected.
Interior light
Lights up when attempted break-in or theft is detected.
Vehicle horns
Sounds when attempted break-in or theft is detected.
Door courtesy light switch
Detects door status (open or closed).
Door lock position switch
Detects door status (locked or unlocked).
Engine hood courtesy switch
Detects engine hood status (open or closed).
Luggage compartment door courtesy switch
Detects luggage compartment door status (open or closed).
Luggage compartment door lock cylinder
Detects luggage compartment door status (locked or unlocked).

ACTIVE ARMING MODE

HINT:
Active arming mode starts the alarm control immediately after the doors are locked.

  1. Active arming mode:
    This system activates as described in the diagram below when one of the items for each condition is met.
    B144373E01

    HINT:
    1. *1: Disarmed state 1 is the normal disarmed state.
    2. *2: Disarmed state 2 is set from either the disarmed state 1 or arming preparation state.

    Condition
    Item
    Condition (1)
    In the disarmed state 1, when the key is not in the key cylinder, the system state is switched if one of the following conditions is met.
    1. With all doors, engine hood and luggage compartment door closed, lock all doors by key operation.
    2. With all doors, engine hood and luggage compartment door closed, lock all doors by wireless operation.
    3. With the engine hood and luggage compartment door closed, close and lock the open door without using the key.
    Condition (2)
    1. After condition (1) is met, allow approx. 30 seconds to elapse.
    Condition (3)
    1. Unlock all doors or only driver's door by wireless operation.
    2. Unlock all doors or only driver's door by key operation.
    3. Unlock any door.
    4. Open any door.
    5. Open the engine hood.
    6. Open the luggage compartment door.
    7. Insert the key into the ignition key cylinder.
    8. Turn the ignition switch to the ON or ACC position.
    9. Reconnect the battery.
    Condition (4)
    1. Open the engine hood.
    2. Open the luggage compartment door.
    3. Reconnect the battery.
    4. Open any door.
    5. Unlock any door when all doors are locked.
    6. Turn the ignition switch to the ON position without using the key.
    Condition (5)
    1. Unlock only driver's door or all doors by wireless operation.
    2. Unlock only driver's door or all doors by key operation.
    3. Turn the ignition switch to the ON position and run the engine for more than 2 seconds.
    Condition (6)
    1. After approx. 30 seconds, the alarm stops and the system returns to the armed state.
    Condition (7)
    1. Open the luggage compartment door by wireless operation.
    2. Unlock the luggage compartment door by key operation.
    Condition (8)
    1. Close the engine hood when the luggage compartment door is closed.
    2. Close the luggage compartment door when the engine hood is closed.
    Condition (9)
    1. Unlock any door when all doors are locked.
    2. Open any door.
    3. Insert the key into the ignition key cylinder.
    4. Turn the ignition switch to the ON or ACC position.
    5. Reconnect the battery.
    Condition (10)
    In the disarmed state 1, when the key is not in the key cylinder, the system state is switched if one of the following conditions is met.
    1. With all doors closed, and the engine hood or luggage compartment door open, lock all doors by wireless operation.
    2. With all doors closed, and the engine hood or luggage compartment door open, lock all doors by key operation.
    3. With the engine hood or luggage compartment door open and all doors locked with any door still open, close the open door.


FORCED DOOR LOCK CONTROL
  1. The forced door lock control prevents the vehicle from being tampered with. Immediately after a door is unlocked (alarm starts), the door is forced to lock by a forced door lock signal.

    1. Conditions that force the doors to lock:
      When the key is not in the key cylinder and the following condition is met:

      1. The theft deterrent system is in the alarm sounding state of active arming mode.


PANIC ALARM CONTROL
  1. The panic alarm control makes it possible to voluntarily set off the panic alarm by pressing the PANIC switch on the wireless transmitter.

    1. Conditions that cause the panic alarm control to set off the panic alarm:
      The panic alarm control sets off the panic alarm by pressing the PANIC switch on the wireless transmitter under the following conditions:

      1. The ignition switch is OFF.
      2. The theft deterrent system is not in the alarm sounding state.

    2. Conditions that cause the panic alarm control to shut off the alarm:
      The panic alarm control shuts off the panic alarm when any of the following conditions is met during panic alarm operation:

      1. The ignition switch is ON.
      2. The panic alarm switch is turned on again.
      3. Any of the switches on the wireless transmitter (LOCK/UNLOCK or LUGGAGE OPEN) is pressed.
      4. The panic alarm ends (approx. 30 sec. have passed).
      5. The theft deterrent system switches to the alarm sounding state. Under this condition, the theft deterrent system is controlling the alarm rather than the panic alarm control. In order to cancel this alarm, refer to the theft deterrent system alarm sounding state cancellation procedure.


SECURITY INDICATOR OUTPUT
  1. The main body ECU outputs a signal to light up the security indicator, according to the state of the theft deterrent system. However, some of the actual lighting conditions of the security indicator are different from the output signals of the main body ECU.

    Output: 
    State of Theft Deterrent System
    Security Indicator
    Output Signals from Main Body ECU
    Actual Lighting Condition
    Disarmed state
    OFF
    OFF (Immobiliser system unset)
    BLINKING (Immobiliser system set)
    Arming preparation state
    ON
    ON
    Armed state
    OFF
    BLINKING
    Alarm sounding state
    ON
    ON
    Blinking cycle: 
    Time
    Security Indicator
    0.2 sec.
    ON
    1.8 sec.
    OFF

    HINT:
    When the immobiliser system is set, the security indicator blinks during both the disarmed state and the armed state, due to the output signals from the immobiliser system.

← SYSTEM DIAGRAM (from Jun 2009)SYSTEM DESCRIPTION (from Jun 2009) →