2006-2011 Camry Aurion · Service Manual TRANSMISSION

P0989 Transmission Fluid Pressure Sensor / Switch "E" Circuit Low

Diagnostic trouble codes · Vehicles built from Oct 2006

Also covers:

DESCRIPTION

ATF pressure switch No. 3 is installed in the lockup solenoid ATF output passage and is used to detect a malfunction in the lockup solenoid.
DTC No.
DTC Detection Condition
Trouble Area
P0989
Transmission fluid pressure switch No. 3 is OFF when lock-up occurs in response to a lock-up request (2-trip detection logic).
  1. ATF temperature sensor assembly (ATF pressure switch No. 3)
  1. Transmission wire
  1. TCM
P0990
When both of the following are detected (2-trip detection logic):
  1. Transmission fluid pressure switch No. 3 is ON when lock-up does not occur.
  2. Lock-up does not occur when shift solenoid valve (SLU) is requested to turn off in the lock-up range.

MONITOR DESCRIPTION

The TCM illuminates the MIL and stores the DTC when the TCM detects that the ATF pressure switch is OFF with the lock-up solenoid ON or when the TCM detects that the ATF pressure switch is ON with the lock-up solenoid OFF.

WIRING DIAGRAM

C133258E16

INSPECTION PROCEDURE


1. CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0989 OR P0990)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the intelligent tester on.

  1. Enter the following items: "Powertrain / ECT / DTC / Current or Pending".

  1. Read the DTCs using the intelligent tester.

    Result:
    Display (DTC output)
    Proceed to
    Only "P0990" is output
    A
    Only "P0989" is output
    B
    "P0989 or P0990" and other DTCs are output
    C

    HINT:
    If a solenoid is stuck OFF, DTCs for several solenoids including the malfunctioning solenoid will be detected.



B
Go to step 4

C
GO TO DTC CHART
A


2. CHECK TRANSMISSION WIRE (SHORT TO GROUND)

  1. C133212E12
    Remove the TCM.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Condition
    Specified Condition
    19 (TPS3) - Body ground (Valve body assembly)
    10 kΩ or higher



OK
REPLACE TCM
NG


3. CHECK ATF TEMPERATURE SENSOR ASSEMBLY (ATF PRESSURE SWITCH NO. 3)

  1. C142709E01
    Disconnect the connector from the ATF temperature sensor assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Condition
    Specified Condition
    5 (TPS3) - Body ground (Valve body assembly)
    10 kΩ or higher



NG
REPLACE ATF TEMPERATURE SENSOR ASSEMBLY
OK

REPLACE TRANSMISSION WIRE

4. CHECK TRANSMISSION WIRE

  1. C133269E07
    Remove the TCM.

  1. Disconnect the speed sensor connector from the transmission wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Condition
    Specified Condition
    19 (TPS3) - 5 (TPS3)
    Below 1 Ω
    19 (TPS3) or 5 (TPS3) - Body ground (Valve body assembly)
    10 kΩ or higher



NG
REPLACE TRANSMISSION WIRE
OK

REPLACE ATF TEMPERATURE SENSOR ASSEMBLY


← P0877 Transmission Fluid Pressure Sensor / Switch "D" Circuit Low (+ P0878) (from Oct 2006)P2714 Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT) (Oct 2006 – May 2009) →