Home › ENGINE › 2AZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM
ECM Power Source Circuit
Circuit diagnosis · Vehicles built Jun 2006 – May 2009
Versions by build date: Jun 2006 – May 2009 from Jun 2009
DESCRIPTION
When the ignition switch is turned to the ON position, the battery voltage is applied to IGSW of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil, closing the contacts of the engine room J/B (EFI relay) and supplying power to either terminal +B or +B2 of the ECM. WIRING DIAGRAM
INSPECTION PROCEDURE
1. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
Disconnect the C24 ECM connector.
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection
Specified Condition
E1 (C24-104) - Body ground
Below 1 Ω
Reconnect the ECM connector.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - BODY GROUND)
OK
2. INSPECT ENGINE ROOM J/B (EFI RELAY VOLTAGE)
Remove the engine room J/B from the engine room R/B.
Disconnect the 1E engine room J/B connector.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
Standard voltage:
Tester Connection
Specified Condition
1E-12 - Body ground
9 to 14 V
Reconnect the engine room J/B connector.
Reinstall the engine room J/B.
OK
NG
3. INSPECT FUSE (EFI MAIN FUSE)
Inspect the EFI MAIN fuse.
Remove the EFI MAIN fuse from the engine room R/B.
Measure the EFI MAIN fuse resistance.
Standard resistance:
Below 1 Ω
Reinstall the EFI MAIN fuse.
NG
REPLACE FUSE (EFI MAIN FUSE)
OK
CHECK AND REPAIR HARNESS AND CONNECTOR (BATTERY - EFI RELAY)
4. INSPECT ENGINE ROOM J/B (EFI RELAY)
Remove the engine room J/B from the engine room R/B.
Inspect the EFI relay.
Measure the EFI relay resistance.
Standard resistance:
Tester Connection
Specified Condition
1E-6 - 1E-12
10 kΩ or higher
Below 1 Ω (Apply battery voltage between terminals 1E-9 and 1E-11)
Reinstall the engine room J/B.
NG
OK
5. INSPECT FUSE (EFI NO. 2 FUSE)
Inspect the EFI No. 2 fuse.
Remove the EFI No. 2 fuse from the engine room R/B.
Measure the EFI No. 2 fuse resistance.
Standard resistance:
Below 1 Ω
Reinstall the EFI No. 2 fuse.
NG
REPLACE FUSE (EFI NO. 2 FUSE)
OK
6. CHECK HARNESS AND CONNECTOR (EFI RELAY - ECM)
Disconnect the A24 ECM connector.
Remove the engine room J/B from the engine room R/B.
Disconnect the 1E engine room J/B connector.
Measure the resistance according to the value(s) in the table below.
Standard resistance (Check for open):
Tester Connection
Specified Condition
+B (A24-2) - 1E-6
Below 1 Ω
+B2 (A24-1) - 1E-6
Below 1 Ω
Standard resistance (Check for short):
Tester Connection
Specified Condition
+B (A24-2) or 1E-6 - Body ground
10 kΩ or higher
+B2 (A24-1) or 1E-6 - Body ground
10 kΩ or higher
Reconnect the ECM connector.
Reconnect the engine room J/B connector.
Reinstall the engine room J/B.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
7. INSPECT ECM (IGSW VOLTAGE)
Disconnect the A24 and C24 ECM connectors.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
Standard voltage:
Tester Connection
Specified Condition
IGSW (A24-28) - E1 (C24-104)
9 to 14 V
Reconnect the ECM connectors.
OK
NG
8. INSPECT FUSE (IGN FUSE)
Remove the IGN fuse from the instrument panel J/B.
Measure the fuse resistance.
Standard resistance:
Below 1 Ω
Result:
Result
Proceed to
OK (RHD)
A
OK (LHD)
B
NG
C
Reinstall the fuse.
B
C
A
9. INSPECT IGNITION RELAY NO. 2
Remove the IG2 relay from the engine room R/B.
Measure the resistance between the terminals.
Standard resistance:
Tester Connection
Specified Condition
3 - 5
10 kΩ or higher
Below 1 Ω (Apply battery voltage between terminals 1 and 2)
Reinstall the IG2 relay.
NG
REPLACE IGNITION RELAY NO. 2
OK
10. CHECK HARNESS AND CONNECTOR (IG2 RELAY - BODY GROUND)
Remove the IG2 relay from the engine room R/B.
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection
Specified Condition
IG2 relay terminal 2 - Body ground
Below 1 Ω
Reinstall the IG2 relay.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
11. INSPECT IGNITION SWITCH ASSEMBLY
Disconnect the E23 ignition switch connector.
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection
Ignition Switch Position
Specified Condition
All Terminals
LOCK
10 kΩ or higher
2 - 4
ACC
Below 1 Ω
1 - 2 - 4, 5 - 6
ON
1 - 3 - 4, 5 - 6 - 7
START
Reconnect the ignition switch connector.
NG
REPLACE IGNITION SWITCH ASSEMBLY
OK
REPAIR OR REPLACE HARNESS OR CONNECTOR
12. CHECK HARNESS AND CONNECTOR (EFI RELAY - ECM, EFI RELAY - BODY GROUND)
Disconnect the A24 ECM connector.
Remove the engine room J/B from the engine room R/B.
Disconnect the 1E engine room J/B connector.
Measure the resistance according to the value(s) in the table below.
Standard resistance (Check for open):
Tester Connection
Specified Condition
MREL (A24-44) - 1E-9
Below 1 Ω
1E-11 - Body ground
Below 1 Ω
Standard resistance (Check for short):
Tester Connection
Specified Condition
MREL (A24-44) or 1E-9 - Body ground
10 kΩ or higher
Reconnect the ECM connector.
Reconnect the engine room J/B connector.
Reinstall the engine room J/B.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK