2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

INSTALLATION

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL STEERING PAD SWITCH ASSEMBLY (for 4 Spoke)

  1. E136758E01
    Engage the 2 pins and install the steering pad switch assembly.

  1. Install the screw and engage the clamp.

    Torque:
    2.4 N*m{ 24 kgf*cm , 21 in.*lbf }

  1. E136757E01
    Engage the 2 pins and install the steering pad switch assembly.

  1. Install the screw and engage the clamp.

    Torque:
    2.4 N*m{ 24 kgf*cm , 21 in.*lbf }

  1. Connect the connector to the spiral cable.


2. INSTALL STEERING PAD SWITCH LH (for 4 Spoke)

  1. E136757E01
    Engage the 2 pins and install the steering pad switch assembly LH.

  1. Install the screw and engage the clamp.

    Torque:
    2.4 N*m{ 24 kgf*cm , 21 in.*lbf }

  1. Connect the connector to the spiral cable.


3. INSTALL STEERING PAD SWITCH ASSEMBLY (for 3 Spoke)

  1. E136761E01
    Engage the 2 pins and install the steering pad switch assembly.

  1. Install the screw and engage the clamp.

    Torque:
    2.4 N*m{ 24 kgf*cm , 21 in.*lbf }

  1. E136760E01
    Engage the 2 pins and install the steering pad switch assembly.

  1. Install the screw and engage the clamp.

    Torque:
    2.4 N*m{ 24 kgf*cm , 21 in.*lbf }

  1. Connect the connector to the spiral cable.


4. INSTALL STEERING PAD SWITCH LH (for 3 Spoke)

  1. E136759E01
    Engage the 2 pins and install the steering pad switch LH.

  1. Install the screw and engage the clamp.

    Torque:
    2.4 N*m{ 24 kgf*cm , 21 in.*lbf }

  1. Connect the connector to the spiral cable.


5. INSTALL STEERING PAD
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C133859E01
    Support the steering pad with one hand.

  1. Connect the 2 airbag connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Connect the horn connector to the steering pad.

  1. Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.

  1. C146015E01
    Using a "TORX" socket (T30), tighten the 2 "TORX" screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }


6. INSTALL LOWER NO. 3 STEERING WHEEL COVER

  1. Engage the claw and install the No. 3 lower steering wheel cover.

    C146016E01


7. INSTALL LOWER NO. 2 STEERING WHEEL COVER

  1. Engage the claw and install the No. 2 lower steering wheel cover.

    C146017E01


8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

9. INSPECT SRS WARNING LIGHT
Inspect the SRS warning light (Click here).
← INSTALLATION (Jun 2006 – Sep 2006)INSTALLATION (from Jun 2009) →