2006-2011 Camry Aurion · Service Manual HEATER & AIR CONDITIONING SYSTEM

REMOVAL

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Oct 2006 – May 2009 from Jun 2009


1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start up the engine.

  1. Turn the A/C switch on.

  1. Operate the cooler compressor at an engine speed of approximately 1,000 rpm for 5 to 6 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the A/C system to collect in the A/C compressor.

  1. Stop the engine.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

3. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. A140800
    Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the cover. Continue to raise the cover to disengage the clip on the rear of the cover and remove the cover.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the cover to break.


4. REMOVE COOL AIR INTAKE DUCT SEAL

  1. A141576E01
    Remove the 7 clips and intake duct seal.


5. REMOVE AIR CLEANER INLET ASSEMBLY

  1. A132969
    Remove the 2 bolts, clamp and air cleaner inlet.


6. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

  1. A135704
    Disconnect the 3 vacuum hoses.

  1. A135705E01
    Disconnect the mass air flow meter connector (*1).

  1. Disconnect the No. 2 ventilation hose (*2).

  1. Disconnect the hose band (*3).

  1. A135706
    Disconnect the 3 bands, and remove the air cleaner cap sub-assembly.


7. REMOVE NO. 1 AIR CLEANER INLET

  1. A132970
    Remove the bolt and No. 1 air cleaner inlet.


8. REMOVE FRONT BUMPER ASSEMBLY (w/o Fog Light)

  1. B160025E01
    Put protective tape around the front bumper assembly.

  1. B149626E01
    Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. B160026
    Remove the 8 screws, 3 clips and 2 radiator grille protectors.

  1. B160027
    Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Remove the front bumper assembly.


9. REMOVE FRONT BUMPER ASSEMBLY (w/ Fog Light)

  1. B160028E01
    Put protective tape around the front bumper assembly.

  1. B149626E01
    Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. B160029
    Remove the 8 screws, 3 clips and 2 radiator grille protectors.

  1. B159433
    Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Disconnect each connector, and then remove the front bumper assembly.


10. REMOVE FRONT BUMPER ASSEMBLY (w/ Clearance Sonar System)

  1. B160028E01
    Put protective tape around the front bumper assembly.

  1. B149626E01
    Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. B160029
    Remove the 8 screws, 3 clips and 2 radiator grille protectors.

  1. B159433
    Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Disconnect each connector, and then remove the front bumper assembly.


11. REMOVE FRONT BUMPER ASSEMBLY (w/ Headlight Cleaner System)

  1. B160028E01
    Put protective tape around the front bumper assembly.

  1. B149626E01
    Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. B160029
    Remove the 8 screws, 3 clips and 2 radiator grille protectors.

  1. B159433
    Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.

    HINT:
    Use the same procedure for the RH side and LH side.

  1. Disconnect each connector.

  1. B149621
    Disconnect the headlight cleaner washer hose, and then remove the front bumper assembly.


12. REMOVE RADIATOR SUPPORT UPPER
  1. Disconnect the horn connectors.

  1. A149528
    Remove the 5 bolts and radiator support upper.


13. REMOVE HOOD LOCK SUPPORT SUB-ASSEMBLY

  1. E129983
    Remove the bolt and hood lock support sub-assembly.


14. DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY

  1. E128544
    Remove the bolt and disconnect the air conditioning tube assembly from the condenser.

  1. Remove the O-ring from the air conditioning tube assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.


15. DISCONNECT COOLER REFRIGERANT DISCHARGE PIPE

  1. E128545
    Remove the bolt and disconnect the cooler refrigerant discharge pipe from the condenser.

  1. Remove the O-ring from the cooler refrigerant discharge pipe.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.


16. REMOVE COOLER CONDENSER ASSEMBLY

  1. E129141
    Remove the 4 bolts and condenser.


17. REMOVE COOLER DRYER

  1. E101931
    Using a 14 mm straight hexagon wrench, remove the cap from the modulator.

  1. E050386
    Using pliers, remove the cooler dryer.

← COMPONENTS (from Oct 2006)REMOVAL (from Jun 2009) →