2006-2011 Camry Aurion · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Oct 2006


1. INSTALL DIFFERENTIAL SIDE GEAR

  1. C138528
    Coat the 2 front differential side gears, 2 side gear thrust washers, 2 front differential pinions and 2 pinion thrust washers with ATF and install them to the differential case.


2. INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

  1. C138706
    Coat the front No. 1 differential pinion shaft with ATF, and install it to the differential case.


3. INSPECT DIFFERENTIAL SIDE GEAR BACKLASH

  1. C083562
    Hold the differential case in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Place a dial indicator on the tip of the side gear tooth at a right angle.

  1. Hold the pinion gear in the differential case and measure the backlash of the side gear.

    Standard backlash:
    0 to 0.15 mm (0 to 0.0059 in.)

    Thrust washer thickness 
    Thickness
    Thickness
    1.50 mm (0.0591 in.)
    1.75 mm (0.0689 in.)
    1.55 mm (0.0610 in.)
    1.80 mm (0.0709 in.)
    1.60 mm (0.0630 in.)
    1.85 mm (0.07283 in.)
    1.65 mm (0.0650 in.)
    1.90 mm (0.07480 in.)
    1.70 mm (0.0669 in.)
    -
    If the backlash is greater than the standard range, select another side gear thrust washer.


4. INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

  1. C138707
    Using a pin punch (3 mm) and hammer, install the pinion shaft straight pin.

    NOTICE:
    Align the holes, and install the pinion shaft straight pin.

  1. C138711
    Using a chisel and hammer, stake the differential case.

    NOTICE:
    Stake the differential case after adjusting the backlash.


5. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

  1. C138712E01
    Using SST and a press, install the front differential case rear tapered roller bearing to the differential case.
    SST
    09726-36010  
    09950-70010   (09951-07100)

    NOTICE:
    Do not damage the bearing cage during bearing inner race installation.

  1. C138714E01
    Using SST and a hammer, install the front differential case rear tapered roller bearing outer race to the transaxle case.
    SST
    09950-60020   (09951-00890)
    09950-70010   (09951-07150)

    NOTICE:
    Ensure that there is no clearance between the bearing and transaxle case.


6. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

  1. C201522E01
    Using SST and a press, install the front differential case front tapered roller bearing to the differential case.
    SST
    09710-30012   (09710-04081)
    09950-60010   (09951-00480)
    09950-70010   (09951-07100)

    NOTICE:
    Do not damage the bearing cage during bearing inner race installation.

  1. Install the shim to the transaxle housing.

  1. C138715E01
    Using SST and a hammer, install the front differential case front tapered roller bearing outer race to the transaxle housing.
    SST
    09950-60020   (09951-00890)
    09950-70010   (09951-07150)

    NOTICE:
    Ensure that there is no clearance between the bearing and transaxle housing.


7. ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

  1. C136467
    Install the differential assembly to the transaxle case.

  1. Clean the contact surfaces of the transaxle case and transaxle housing.

  1. C136447E01
    Install the transaxle housing to the transaxle case with the 20 bolts.

    Torque:
    Bolt A:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }
    Bolt B:
    23 N*m{ 234 kgf*cm , 17 ft.*lbf }

  1. C138262E01
    Using SST, turn the differential assembly right and left 2 or 3 times to settle the bearing.
    SST
    09564-33010  

  1. Using SST and a torque wrench, measure the turning torque of the differential side bearing while rotating SST at 10 rpm.

    SST
    09564-33010  

    Turning torque:
    1.05 to 1.93 N*m (10.70 to 19.67 kgf*cm, 9.29 to 17.08 in.*lbf)

    If the turning torque is not within the specified range, refer to the table below to select a shim so that the turning torque is within the specified range.
    Shim thickness: mm (in.) 
    Thickness
    Thickness
    Thickness
    Thickness
    2.000 (0.0787)
    2.225 (0.0876)
    2.450 (0.0965)
    2.675 (0.1054)
    2.025 (0.0797)
    2.250 (0.0886)
    2.475 (0.0974)
    2.700 (0.1063)
    2.050 (0.0807)
    2.275 (0.0896)
    2.500 (0.0984)
    2.725 (0.1073)
    2.075 (0.0817)
    2.300 (0.0906)
    2.525 (0.0994)
    2.750 (0.1083)
    2.100 (0.0827)
    2.325 (0.0915)
    2.550 (0.1004)
    2.775 (0.1093)
    2.125 (0.0837)
    2.350 (0.0925)
    2.575 (0.1014)
    2.800 (0.1102)
    2.150 (0.0847)
    2.375 (0.0935)
    2.600 (0.1024)
    2.825 (0.1112)
    2.175 (0.0856)
    2.400 (0.0945)
    2.625 (0.1034)
    2.850 (0.1122)
    2.200 (0.0866)
    2.425 (0.0955)
    2.650 (0.1043)
    2.875 (0.1132)

  1. C136447
    Remove the 20 bolts and the transaxle housing from the transaxle case.

  1. C136467
    Remove the differential assembly from the transaxle case.


8. INSTALL FRONT DIFFERENTIAL RING GEAR

  1. D025215E05
    Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194.0 to 230.0°F).

    NOTICE:
    Do not heat the ring gear to more than 110°C (230.0°F).

  1. Clean the contact surface of the front differential case.

  1. C138531E01
    Align the matchmarks, and install the front differential ring gear case quickly.

    NOTICE:
    Do not install the bolts while the ring gear is hot.

  1. C138532
    Install and tighten the 12 bolts.

    Torque:
    120 N*m{ 1223 kgf*cm , 88 ft.*lbf }

    NOTICE:
    Tighten the bolts a little at a time in diagonal order.


9. INSTALL TRANSAXLE CASE OIL SEAL
  1. Coat the lip of a new oil seal with MP grease.

  1. C138716E01
    Using SST and a hammer, install the oil seal.
    SST
    09316-10010  
    09950-70010   (09951-07100)

    Oil seal drive in depth:
    -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


10. INSTALL FRONT TRANSAXLE CASE OIL SEAL
  1. Coat the lip of a new oil seal with MP grease.

  1. C138717E01
    Using SST and a hammer, install the oil seal.
    SST
    09308-14010  

    Oil seal drive in depth:
    -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

← INSPECTION (from Oct 2006)COMPONENTS (from Oct 2006) →