SYSTEM DESCRIPTION
Troubleshooting · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
| EXTERIOR LIGHT CONTROL SYSTEM |
- Automatic Light Control
- Manual Light Control
- High Beam Control
- Passing Light Control
- Front Fog Light Control
- Light Auto Turn off Control
Automatic Light Control


General
When the light control switch is in the AUTO position, the automatic light control sensor detects ambient light levels and outputs it to the main body ECU. The main body ECU controls the low beam headlights and taillights (parking lights, taillights and license plate lights) according to the signal. By this function, when driving at night, when going into tunnel etc, the taillights and low beam headlights come on automatically. If the timing of lights ON/OFF does not meet the user's feeling, the sensitivity of automatic light control system can be changed using the intelligent tester.Fail-Safe
If the main body ECU detects a malfunction in the automatic light control sensor, the main body ECU effects fail-safe control to prohibit the automatic light control. If the headlights or taillights are on, the lights will maintain the ON status until the light control switch is turned off.
Manual Light Control
General
The function is similar to the automatic light control, except the function is controlled according to the driver's inputs.When the light control switch is turned to the TAIL position, the main body ECU turns the taillights on. When the light control switch is turned to the HEAD position, the main body ECU turns the low beam headlights and taillights on.
High Beam Control
General
High beam control functions to illuminate farther ahead than normal.When either of the following conditions is met, the high beam headlights come on:
- Dimmer switch is in HIGH position and light control switch is in HEAD position.
- Dimmer switch is in HIGH position, light control switch is in AUTO position and low beam headlights are on.
- Dimmer switch is in HIGH position and light control switch is in HEAD position.
Passing Light Control
General
Passing light control functions to illuminate the high beam headlights in order to allow an oncoming vehicle to become aware of the vehicle's presence while driving with poor visibility.When the dimmer switch is turned to the HIGH FLASH position, the high beam headlights come on.
Front Fog Light Control
General
The front fog light control functions to maintain visibility in the road ahead of the vehicle while driving with poor visibility, such as when driving in a dense fog.When both of the following conditions are met, the front fog lights come on:
- Taillights are ON.
- Front fog light switch is ON.
- Taillights are ON.
When either of the following conditions is met, the front fog lights turn off:
- Front fog light switch is OFF.
- Taillights are OFF.
- Front fog light switch is OFF.
Auto Turn off Control


General
The light auto turn-off system is used to prevent the driver from leaving the vehicle with the headlights, fog lights, parking lights, taillights, or license plate lights on.When all of the following conditions are met, the exterior lights turn off:
- Ignition switch is turned from on (ACC or IG) to off.
- Headlights, fog lights or taillights are on.
- Driver side door is opened.
- Ignition switch is turned from on (ACC or IG) to off.
| POWER DISTRIBUTOR |
General
- The power distributor is built into the engine room relay block, and uses a small mechanical relay and semiconductor relay for a compact and lightweight design.
- When a short circuit occurs between the power distributor and high beam headlight bulb, a fail-safe function operates to stop the high beam headlight relay operation.


- The power distributor is built into the engine room relay block, and uses a small mechanical relay and semiconductor relay for a compact and lightweight design.
The components of the power distributor are shown below.
Component
Relay
Mechanical Relay
- Horn Relay
- A/F Relay
- Security Horn Relay
- EFI Relay
- Circuit Opening Relay
- Headlight Relay RH*1
- Headlight Relay LH*1
Semiconductor Relay
- High Beam Headlight Relay
- Headlight Relay RH*2
- Headlight Relay LH*2
- HINT:
- *1: for halogen headlight
- *2: for HID headlight
- *1: for halogen headlight
- Horn Relay
| HID HEADLIGHT SYSTEM |
General
The HID (High Intensity Discharge) headlight system uses a discharge bulb as its light source for the low beam. Discharge bulbs are superior to halogen bulbs.- Discharge bulbs have the following features:
- The light emitted by the bulb is close in color to sunlight. The light shines ahead over a broader area and further forward, increasing the area visible to the driver.
- Less power is consumed.
- This system consists of the discharge bulbs and light control ECUs.
- The light control ECU transforms the voltage that is input from the battery to a high voltage of up to 20,000 V and applies it to the discharge bulbs in order to illuminate them.
- A fail-safe function is provided as a countermeasure against the high voltage that is generated in case that a problem occurs in the headlight system.
- Discharge bulbs have the following features:
| ILLUMINATION CONTROL SYSTEM (ILLUMINATED ENTRY SYSTEM) |
General
- The illuminated entry system controls the interior light, ignition key cylinder light*1/engine switch illumination*2.
- The interior light is operated when the light switch is in the DOOR position.
- HINT:
-
*1: without Smart Entry and Start System
-
*1: without Smart Entry and Start System
-
*2: with Smart Entry and Start System
-
*2: with Smart Entry and Start System
- The illuminated entry system controls the interior light, ignition key cylinder light*1/engine switch illumination*2.
Interior Light Control
- The interior light control (interior light, ignition key cylinder light*1/engine switch illumination*2) consists primarily of the fade-in/fade-out function and timer illumination function.
- This function provides convenience when getting in or out of the vehicle at night.
- This function is controlled by the main body ECU. The operation and condition of this control are described below.
Operation
Condition
Fade in
When any of the following conditions is met, the interior light and ignition key cylinder light/engine switch illumination fade in. - Any door is opened.
- Any door is unlocked when the ignition switch is off and all doors are closed.
- Ignition switch is turned from ACC to off when all doors are closed.
Fade out immediately
When either of the following conditions is met, the interior light and ignition key cylinder light/engine switch illumination fade out. - Ignition switch is turned from off to ACC or ON when all doors are closed.
- All doors are locked when the ignition switch is off.
Illuminate for approximately 15 seconds, and then fade out
All doors are closed when the ignition switch is off.
- Any door is opened.
- The interior light control (interior light, ignition key cylinder light*1/engine switch illumination*2) consists primarily of the fade-in/fade-out function and timer illumination function.
Battery Saving Control
General
If the vehicle is left with the doors open for a long time, this function will operate to automatically turn off the lights illuminated by the illuminated entry function.Battery saving control is controlled by the main body ECU. When all of the following conditions have been met, the main body ECU turns off the lights.
- A key is not inserted in the ignition key cylinder. *1
- The key is not in the actuation area. *2
- There is no change in the condition of the doors for 20 minutes.
- A key is not inserted in the ignition key cylinder. *1
When any of the following conditions is met, the count of the battery save times will be cleared.
- A key is inserted in the ignition key cylinder. *1
- A key is in the actuation area. *2
- Any of the doors is opened.
- HINT:
-
*1: without Smart Entry and Start System
-
*2: with Smart Entry and Start System
-
*1: without Smart Entry and Start System
- A key is inserted in the ignition key cylinder. *1
| AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM |
General
- When the headlights are on, the automatic headlight beam level control system operates the headlight leveling motor in accordance with movement of the vehicle.
- The automatic headlight beam level control system mainly consists of the AFS ECU, rear height control sensor, and two headlight leveling motors. The AFS ECU controls the system.
- The AFS ECU calculates changes in the vehicle posture based on signals from the rear RH height control sensor and each ECU.
- The ECU then controls the headlight leveling motor based on this information, in order to change the headlight reflector angle.
- NOTICE:
- Initialize the height control sensor signal after the vehicle height changes due to replacement of the suspension or after performing such operations as removal and reinstallation or replacement of the rear height control sensor sub-assembly.
- When the AFS ECU is replaced, the initialization is also necessary.
- Initialize the height control sensor signal after the vehicle height changes due to replacement of the suspension or after performing such operations as removal and reinstallation or replacement of the rear height control sensor sub-assembly.
- When the headlights are on, the automatic headlight beam level control system operates the headlight leveling motor in accordance with movement of the vehicle.
Function of Main Components
Component
Outline
AFS ECU
- Calculates changes in the vehicle posture based on the signals from the height control sensor and each ECU.
- Outputs control signal to the headlight leveling actuator, based on the detected value.
- Provides initial set control, fail-safe function and diagnosis function.
Headlight Leveling Motor
- Based on the signals received from the AFS ECU, the motors move the reflectors in the headlights to vary the Lo beam.
- Uses a step motor to precisely regulate the angle of the reflectors.
Rear RH Height Control Sensor
Detects the height of the rear of the vehicle.
Skid Control ECU (with VSC)
Transmits the speed sensor signal (Front LH and RH) to the AFS ECU.
ECM
Transmits the engine running status signal to the AFS ECU.
Main Body ECU
Transmits the headlight status signal.
Combination Meter (Meter ECU)
AFS OFF Indicator Light
When the system malfunctions, the meter ECU alerts the driver by flashing the AFS OFF indicator light in accordance with the signal from the AFS ECU.
- Calculates changes in the vehicle posture based on the signals from the height control sensor and each ECU.
Initial Set Control
When the engine is started, the AFS ECU drives the headlight level actuator and moves the headlight reflector to the lower limit position. Then reflector returns to the proper position. The AFS ECU thus assesses the position of the headlight for reference control.
Fail-Safe

If the AFS ECU detects a malfunction in the automatic headlight beam level control system, the AFS ECU effects fail-safe control. At the same time, the meter ECU flashes the AFS OFF indicator light in order to inform the driver of the problem.
| INTELLIGENT AFS (Adaptive Front-lighting System) |
General
- An intelligent AFS (Adaptive Front-lighting System) is used in order to ensure a wide Lo beam lighting area and realize excellent visibility during turns by moving the Lo beam.
- The intelligent AFS uses medium-to-high speed control and low speed control. The system calculates the target lighting angle based on the steering angle, vehicle speed and changes swivel angle of the low-beam headlight on the side facing into the turn.


- An intelligent AFS (Adaptive Front-lighting System) is used in order to ensure a wide Lo beam lighting area and realize excellent visibility during turns by moving the Lo beam.
Function of Main Components
Component
Outline
AFS ECU
The AFS ECU receives various signals, calculates the target lighting angle, and actuates the headlight swivel actuator.
Headlight Swivel Motor
- Driven by the AFS ECU, the motor moves the low beam left or right to the angle calculated by the AFS ECU.
- A step motor is used for the headlight swivel motor. The AFS ECU determines the low beam angle based on the number of steps (position) of the step motor.
Steering Angle Sensor
Detects the steering angle and direction and outputs this signal to the AFS ECU.
AFS OFF Switch
Pressing this switch disables the operation of the intelligent AFS.
Skid Control ECU
Transmits the speed sensor signal (Front LH and RH) to the AFS ECU.
ECM
- Transmits the engine running status signal to the AFS ECU.
- Transmits the shift position signal to the AFS ECU. The AFS ECU determines whether the vehicle is moving forward or backward from this signal.
Main Body ECU
Transmits the headlight status signal.
Combination Meter (Meter ECU)
AFS OFF Indicator Light
- When the system malfunctions, the meter ECU flashes the AFS OFF indicator light based on the signal from the AFS ECU to alert the driver.
- When the AFS OFF switch is ON (pushed), the meter ECU turns on the AFS OFF indicator.
- Driven by the AFS ECU, the motor moves the low beam left or right to the angle calculated by the AFS ECU.
Low Speed Control
The AFS ECU performs the low speed control when all the following conditions are fulfilled.- Engine is running.
- Vehicle is moving forward at a speed of 10 km/h (6 mph) or more, and less than 30 km/h (19 mph).
- Steering angle is 6° or more.
- Low beam headlights are ON.
- AFS OFF switch is OFF.
Swivel Angle Range (RHD): Driving Condition
Low Beam
Left
Right
Right Turn
0° Fixed
0° to 15° to Right
Left Turn
0° to 10° to Left
0° Fixed
Swivel Angle Range (LHD): Driving Condition
Low Beam
Left
Right
Right Turn
0° Fixed
0° to 10° to Left
Left Turn
0° to 15° to Right
0° Fixed
- Engine is running.
Medium-to-high Speed Control
The AFS ECU performs the medium-to-high speed control when all the following conditions are fulfilled.- Engine is running.
- Vehicle is moving forward at a speed of 30 km/h (19 mph) or more.
- Steering angle is 7.5° or more.
- Low beam headlights are ON.
- AFS OFF switch is OFF.
Swivel Angle Range (RHD): Driving Condition
Low Beam
Left
Right
Right Turn
0° Fixed
0° to 15° to Right
Left Turn
0° to 10° to Left
0° Fixed
Swivel Angle Range (LHD): Driving Condition
Low Beam
Left
Right
Right Turn
0° Fixed
0° to 10° to Left
Left Turn
0° to 15° to Right
0° Fixed
- Engine is running.
Initial Set Control
When the engine is started, the AFS ECU drives the headlight swivel actuator and moves the projector headlight to the operation limit in the direction toward the vehicle center and returns it to the proper position. The AFS ECU thus assesses the position of the headlight for reference control.Fail-Safe
If the AFS ECU detects a malfunction in the intelligent AFS, the AFS ECU effects fail-safe control. At the same time, the meter ECU flashes the AFS OFF indicator light in order to inform the driver of the problem.