Item
|
Outline
|
Detection of abnormal input voltage (High input voltage)
|
If voltage that is input to the light control ECU is approximately 20 V or more, the ECU stops illuminating the headlights, and resumes when the voltage drops to 16 V or less.
|
Detection of abnormal input voltage (Low input voltage)
|
If voltage that is input to the light control ECU is 6 V or less, the ECU stops illuminating the low beam headlights, and resumes when the voltage is 10 V or more.
|
Detection of abnormal output
- Output open
- Short between output terminals
- Short between output terminal and body ground
|
If an abnormal condition occurs in the voltage that is output by the light control ECU, the ECU stops illuminating the low beam headlights and will maintain this state until the power is reinstated (by turning the light control switch from OFF to HEAD).
|
Detection of bulb flashing
|
If the bulb flashing repeats within approximately 5 seconds and continues for approximately 60 seconds, the light control ECU stops illuminating low beam headlights and will maintain this state until the power is reinstated (by turning the light control switch from OFF to HEAD).
|
Detection of abnormal light voltage (Low light voltage)
|
After approximately 80 seconds since input voltage is supplied, if the light voltage is below approximately 31 V and continues for approximately 0.5 seconds, the light control ECU stops illuminating the low beam headlights and will maintain this state until the power is reinstated (by turning the light control switch from OFF to HEAD).
|
Detection of abnormal light voltage (High light voltage)
|
If the light voltage is above approximately 69 V and continues for approximately 0.5 seconds, the light control ECU stops illuminating the low beam headlights and will maintain this state until the power is reinstated (by turning the light control switch from OFF to HEAD).
|
Fail-Safe Control for Automatic Headlight Beam Level Control:
Trouble Area
|
Condition
|
AFS OFF Indicator Light
|
Headlight Swivel Motor Malfunction
|
Continues to control until a position of 0.8° less than the current position is reached.
|
Flash
|
Steering Angle Sensor Signal Malfunction
|
Continues to control.
|
Flash
|
Speed Sensor Signal Malfunction
|
- Continues to control using the normal speed sensor signal if one signal fails.
- Judges that the vehicle speed is 0 km/h and continues to control if both speed sensor signals fail.
|
Flash
|
Height Control Sensor Signal Malfunction
|
- Stops the operation after returning to initial position (Fail at higher than initial position).
- Stops the operation in current condition (Fail at lower than initial position).
|
Flash
|
Headlight Leveling Motor Malfunction
|
Normal Side Headlight Leveling Motor
- Stops the operation after returning to initial position (Fail at higher than initial position).
- Stops in current condition (Fail at lower than initial position).
|
Flash
|
Abnormal Side Headlight Leveling Motor
- Stops in its current position.
|
Communication Signal Malfunction
|
Skid Control ECU:
- Judges that the vehicle speed is 0 km/h (0 mph) and continues to control.
|
Flash
|
Steering Angle Sensor:
- Continues to control.
|
Fail-Safe Control for Intelligent AFS:
Trouble Area
|
Condition
|
AFS OFF Indicator Light
|
Headlight Swivel Motor
|
Normal Side Headlight Swivel Motor:
- Stops operating after returning to the initial position.
|
Flash
|
Abnormal Side Headlight Swivel Motor:
- Stops in its current position.
|
Steering Angle Sensor Signal Malfunction
|
Stops operating after returning to the initial position.
|
Flash
|
Speed Sensor Signal Malfunction
|
Stops operating after returning to the initial position.
|
Flash
|
Height Control Sensor Signal Malfunction
|
Stops operating after returning to the initial position.
|
Flash
|
Headlight Leveling Motor
|
Stops operating after returning to the initial position.
|
Flash
|
Communication Signal Malfunction
|
Main Body ECU:
- Stops operating after returning to the initial position.
|
Flash
|
Engine ECU:
- Stops operating after returning to the initial position.
|
Skid Control ECU:
- Stops operating after returning to the initial position.
|
Steering Angle Sensor:
- Stops operating after returning to the initial position.
|