2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

B2326 CAN MS Bus Line Communication Malfunction

Diagnostic trouble codes · Vehicles built from Oct 2006

DESCRIPTION

  1. The main body ECU will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to the CAN MS bus.
  2. When the main body ECU receives response signals from the ECUs connected to the CAN MS bus, the main body ECU recognizes and memorizes that the ECUs are connected to the CAN MS bus. Based on this memorized data, the main body ECU monitors for malfunctions in the ECUs connected to the CAN MS bus when communicating with those ECUs. If the main body ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN MS bus, the main body ECU determines that a malfunction exists.
DTC No.
DTC Detection Condition
Trouble Area
B2326
Main body ECU cannot receive signals from all ECUs that have been memorized as those connected to the CAN MS bus.
  1. Open or short in CAN MS bus main wire or connector
  2. Open or short in CAN MS bus branch wire or connector
  3. Certification ECU
  4. Clearance warning ECU
  5. Main body ECU
  6. CAN No. 3 J/C

WIRING DIAGRAM

C142750E04

INSPECTION PROCEDURE

NOTICE:
  1. Turn the engine switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
  2. After the engine switch is turned off, check that the key reminder warning system and lighting system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the engine switch, any other switches, or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the engine switch, any switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below will help determine the cause of the malfunction.


1. CHECK CAN MS BUS WIRE

  1. C142737E01
    Turn the engine switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Result:
    Tester Connection
    Condition
    Specified Value
    Proceed to
    O34-1 (CANH) - O34-2 (CANL)
    Engine switch off
    54 to 69 Ω
    A
    O34-1 (CANH) - O34-2 (CANL)
    Engine switch off
    69 Ω or higher
    B
    O34-1 (CANH) - O34-2 (CANL)
    Engine switch off
    Less than 54 Ω
    C



B
Go to step 5

C
Go to step 9
A


2. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE

  1. C144938E01
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O34-1 (CANH) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher
    O34-2 (CANL) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher



NG
Go to step 15
OK


3. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE

  1. C144938E03
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O34-1 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    O34-2 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher



NG
Go to step 20
OK


4. CHECK FOR OPEN IN CAN MS BUS BRANCH WIRE (CAN MS BUS BRANCH WIRE)
  1. Check the clearance warning ECU branch wire (Click here).



NG
REPAIR OR REPLACE CAN MS BUS BRANCH WIRE OR CONNECTOR (CLEARANCE WARNING ECU)
OK

REPLACE INSTRUMENT PANEL J/B (MAIN BODY ECU)

5. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (CERTIFICATION ECU MAIN WIRE)

  1. C142738E01
    Disconnect certification ECU main wire connector O34 from the CAN No. 3 J/C.

    HINT:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O34-1 (CANH) - O34-2 (CANL)
    Engine switch off
    108 to 132 Ω



OK
Go to step 7
NG


6. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (CERTIFICATION ECU - CAN NO. 3 J/C)
  1. Reconnect certification ECU main wire connector O34 to the CAN No. 3 J/C.

  1. C142197E03
    Disconnect certification ECU connector E58.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E58-27 (CANH) - E58-28 (CANL)
    Engine switch off
    108 to 132 Ω



NG
REPLACE CERTIFICATION ECU
OK

REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CERTIFICATION ECU - CAN NO. 3 J/C)

7. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (MAIN BODY ECU - CAN NO. 3 J/C)
  1. Reconnect certification ECU main wire connector O34 to the CAN No. 3 J/C.

  1. C142739E01
    Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

    HINT:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O33-1 (CANH) - O33-2 (CANL)
    Engine switch off
    108 to 132 Ω



OK
REPLACE CAN NO. 3 J/C
NG


8. CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU - CAN NO. 7 J/C)
  1. Reconnect CAN MS bus main wire connector O33 to the CAN No. 3 J/C.

  1. C142209E03
    Disconnect connector E8 from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E8-16 (CANP) - E8-15 (CANN)
    Engine switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 7 J/C - MAIN BODY ECU)
OK

REPLACE INSTRUMENT PANEL J/B (MAIN BODY ECU)

9. CHECK FOR SHORT IN CAN MS BUS WIRES (CAN NO. 3 J/C WIRE)

  1. C142739E01
    Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O33-1 (CANH) - O33-2 (CANL)
    Engine switch off
    108 to 132 Ω



NG
Go to step 14
OK


10. CHECK FOR SHORT IN CAN MS BUS WIRES (CERTIFICATION ECU MAIN WIRE)

  1. C142738E01
    Disconnect certification ECU main wire connector O34 from the CAN No. 3 J/C.

    HINT:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O34-1 (CANH) - O34-2 (CANL)
    Engine switch off
    108 to 132 Ω



OK
Go to step 12
NG


11. CHECK FOR SHORT IN CAN MS BUS WIRES (CERTIFICATION ECU - CAN NO. 3 J/C)

  1. C142197E03
    Disconnect certification ECU connector E58.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E58-27 (CANH) - E58-28 (CANL)
    Engine switch off
    108 to 132 Ω



NG
REPLACE CERTIFICATION ECU
OK

REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CERTIFICATION ECU - CAN NO. 3 J/C)

12. CHECK FOR SHORT IN CAN MS BUS WIRES (CLEARANCE WARNING ECU BRANCH WIRE)
  1. Reconnect certification ECU main wire connector O34 to the CAN No. 3 J/C.

  1. C142740E01
    Disconnect clearance warning ECU main wire connector O32 from the CAN No. 3 J/C.

    HINT:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O32-1 (CANH) - O32-2 (CANL)
    Engine switch off
    1 MΩ or higher



OK
REPLACE CAN NO. 3 J/C
NG


13. CHECK FOR SHORT IN CAN MS BUS WIRES (CLEARANCE WARNING ECU BRANCH WIRE)

  1. C142740E01
    Disconnect clearance warning ECU connector O30.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O32-1 (CANH) - O32-2 (CANL)
    Engine switch off
    1 MΩ or higher



NG
REPAIR OR REPLACE CAN MS BUS BRANCH WIRE OR CONNECTOR (CLEARANCE WARNING ECU - CAN NO. 3 J/C)
OK

REPLACE CLEARANCE WARNING ECU

14. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (MAIN BODY ECU - CAN NO. 3 J/C)

  1. C142209E03
    Reconnect CAN MS bus main wire connector O33 to the CAN No. 3 J/C.

  1. Disconnect connector E8 from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E8-16 (CANP) - E8-15 (CANN)
    Engine switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 3 J/C - MAIN BODY ECU)
OK

REPLACE INSTRUMENT PANEL J/B (MAIN BODY ECU)

15. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (CAN NO. 3 J/C WIRE)

  1. C142739E01
    Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

  1. C126231E14
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O33-1 (CANH) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher
    O33-2 (CANL) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher



NG
Go to step 19
OK


16. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (CERTIFICATION ECU - CAN NO. 3 J/C)

  1. C142738E01
    Reconnect CAN MS bus main wire connector O33 to the CAN No. 3 J/C.

  1. C126231E14
    Disconnect certification ECU main wire connector O34 from the CAN No. 3 J/C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O34-1 (CANH) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher
    O34-2 (CANL) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher



NG
Go to step 18
OK


17. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (CLEARANCE WARNING ECU - CAN NO. 3 J/C)
  1. Reconnect certification ECU main wire connector O34 to the CAN No. 3 J/C.

  1. C142740E01
    Disconnect clearance warning ECU branch wire connector O32 from the CAN No. 3 J/C.

  1. Disconnect connector O30 from the clearance warning ECU.

  1. C126231E14
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O32-1 (CANH) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher
    O32-2 (CANL) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MS BUS BRANCH WIRE OR CONNECTOR (CLEARANCE WARNING ECU BRANCH WIRE)
OK

REPLACE CLEARANCE WARNING ECU

18. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (CERTIFICATION ECU - CAN NO. 3 J/C)

  1. C142738E01
    Disconnect certification ECU connector E58.

  1. C126231E14
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O34-1 (CANH) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher
    O34-2 (CANL) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CERTIFICATION ECU MAIN WIRE)
OK

REPLACE CERTIFICATION ECU

19. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (MAIN BODY ECU - CAN NO. 3 J/C)

  1. C142739E01
    Disconnect the main body ECU connector E8 from the main body ECU.

  1. C126231E14
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O33-1 (CANH) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher
    O33-2 (CANL) - E10-16 (BAT)
    Engine switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 3 J/C - MAIN BODY ECU)
OK

REPLACE INSTRUMENT PANEL J/B (MAIN BODY ECU)

20. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CAN NO. 3 J/C WIRE)

  1. C142739E01
    Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

  1. C126231E15
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O33-1 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    O33-2 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher



NG
Go to step 24
OK


21. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CERTIFICATION ECU - CAN NO. 3 J/C)

  1. C142738E01
    Reconnect CAN MS bus main wire connector O33 to the CAN No. 3 J/C.

  1. Disconnect certification ECU main wire connector O34 from the CAN No. 3 J/C.

  1. C126231E15
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O34-1 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    O34-2 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher



NG
Go to step 23
OK


22. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CLEARANCE WARNING ECU - CAN NO. 3 J/C)

  1. C142740E01
    Reconnect certification ECU main wire connector O34 to the CAN No. 3 J/C.

  1. Disconnect clearance warning ECU branch wire connector O32 from the CAN No. 3 J/C.

  1. Disconnect connector O30 from the clearance warning ECU.

  1. C126231E15
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O32-1 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    O32-2 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher



NG
REPAIR OR REPLACE CAN MS BUS BRANCH WIRE OR CONNECTOR (CLEARANCE WARNING ECU BRANCH WIRE)
OK

REPLACE CLEARANCE WARNING ECU

23. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CERTIFICATION ECU - CAN NO. 3 J/C)

  1. C142738E01
    Disconnect certification ECU connector E58.

  1. C126231E15
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O34-1 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    O34-2 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CERTIFICATION ECU MAIN WIRE)
OK

REPLACE CERTIFICATION ECU

24. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (MAIN BODY ECU - CAN NO. 3 J/C)

  1. C142739E01
    Disconnect the main body ECU connector E8 from the main body ECU.

  1. C126231E15
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    O33-1 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    O33-2 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher



NG
REPAIR OR REPLACE CAN MS BUS MAIN WIRE OR CONNECTOR (CAN NO. 3 J/C - MAIN BODY ECU)
OK

REPLACE INSTRUMENT PANEL J/B (MAIN BODY ECU)


← B1297 Clearance Sonar ECU Communication Stop (from Oct 2006)U0182 Lost Communication with AFS ECU (from Jun 2009) →