B2326 CAN MS Bus Line Communication Malfunction
Diagnostic trouble codes · Vehicles built from Oct 2006
DESCRIPTION
- The main body ECU will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to the CAN MS bus.
- When the main body ECU receives response signals from the ECUs connected to the CAN MS bus, the main body ECU recognizes and memorizes that the ECUs are connected to the CAN MS bus. Based on this memorized data, the main body ECU monitors for malfunctions in the ECUs connected to the CAN MS bus when communicating with those ECUs. If the main body ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN MS bus, the main body ECU determines that a malfunction exists.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B2326 |
Main body ECU cannot receive signals from all ECUs that have been memorized as those connected to the CAN MS bus. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Turn the ignition switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
- After the ignition switch is turned off, check that the key reminder warning system and lighting system are not operating.
- Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches, or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.
- Turn the ignition switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
- HINT:
- Operating the ignition switch, any switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
- Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below will help determine the cause of the malfunction.
- Operating the ignition switch, any switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
| 1. CHECK CAN MS BUS WIRE |
Turn the ignition switch off.

Measure the resistance according to the value(s) in the table below.
- Result:
Tester Connection
Condition
Specified Value
Proceed to
O33-1 (CANH) - O33-2 (CANL)
Ignition switch off
54 to 69 Ω
A
O33-1 (CANH) - O33-2 (CANL)
Ignition switch off
69 Ω or higher
B
O33-1 (CANH) - O33-2 (CANL)
Ignition switch off
Less than 54 Ω
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Value
O33-1 (CANH) - E10-16 (BAT)
Ignition switch off
6 kΩ or higher
O33-2 (CANL) - E10-16 (BAT)
Ignition switch off
6 kΩ or higher
|
|
||||
| OK | |
| 3. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Value
O33-1 (CANH) - E10-4 (CG)
Ignition switch off
200 Ω or higher
O33-2 (CANL) - E10-4 (CG)
Ignition switch off
200 Ω or higher
|
|
||||
| OK | |
| 4. CHECK FOR OPEN IN CAN MS BUS BRANCH WIRE |
Check the clearance warning ECU branch wire (Click here).
|
|
||||
| OK | ||
| ||
| 5. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (MAIN BODY ECU - CAN NO. 3 J/C) |
Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

- HINT:
- Before disconnecting the connector, make a note of where it is connected.
- Reconnect the connector to its original position.
- Before disconnecting the connector, make a note of where it is connected.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O33-1 (CANH) - O33-2 (CANL)
Ignition switch off
108 to 132 Ω
|
|
||||
| NG | |
| 6. CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU - CAN NO. 3 J/C) |
Reconnect CAN MS bus main wire connector O33 to the CAN No. 3 J/C.
Disconnect connector E8 from the main body ECU.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
E8-16 (CANP) - E8-15 (CANN)
Ignition switch off
108 to 132 Ω
|
|
||||
| OK | ||
| ||
| 7. CHECK FOR SHORT IN CAN MS BUS WIRES (CAN NO. 3 J/C WIRE) |
Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O33-1 (CANH) - O33-2 (CANL)
Ignition switch off
108 to 132 Ω
|
|
||||
| OK | |
| 8. CHECK FOR SHORT IN CAN MS BUS WIRES (CLEARANCE WARNING ECU BRANCH WIRE) |
Reconnect CAN MS bus main wire connector O33 to the CAN No. 3 J/C.
Disconnect clearance warning ECU branch wire connector O32 from the CAN No. 3 J/C.

- HINT:
- Before disconnecting the connector, make a note of where it is connected.
- Reconnect the connector to its original position.
- Before disconnecting the connector, make a note of where it is connected.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O32-1 (CANH) - O32-2 (CANL)
Ignition switch off
1 MΩ or higher
|
|
||||
| NG | |
| 9. CHECK FOR SHORT IN CAN MS BUS WIRES (CLEARANCE WARNING ECU BRANCH WIRE) |
Disconnect clearance warning ECU connector O30.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O32-1 (CANH) - O32-2 (CANL)
Ignition switch off
1 MΩ or higher
|
|
||||
| OK | ||
| ||
| 10. CHECK FOR OPEN IN CAN MS BUS MAIN WIRE (MAIN BODY ECU - CAN NO. 3 J/C) |
Reconnect CAN MS bus main wire connector O33 to the CAN No. 3 J/C.

Disconnect connector E8 from the main body ECU.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
E8-16 (CANP) - E8-15 (CANN)
Ignition switch off
108 to 132 Ω
|
|
||||
| OK | ||
| ||
| 11. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (CAN NO. 3 J/C WIRE) |
Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Value
O33-1 (CANH) - E10-16 (BAT)
Ignition switch off
6 kΩ or higher
O33-2 (CANL) - E10-16 (BAT)
Ignition switch off
6 kΩ or higher
|
|
||||
| OK | |
| 12. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (CLEARANCE WARNING ECU - CAN NO. 3 J/C) |
Reconnect CAN MS bus main wire connector O33 to the CAN No. 3 J/C.
Disconnect clearance warning ECU branch wire connector O32 from the CAN No. 3 J/C.

Disconnect connector O30 from the clearance warning ECU.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O32-1 (CANH) - E10-16 (BAT)
Ignition switch off
6 kΩ or higher
O32-2 (CANL) - E10-16 (BAT)
Ignition switch off
6 kΩ or higher
|
|
||||
| OK | ||
| ||
| 13. CHECK FOR SHORT TO +B IN CAN MS BUS WIRE (MAIN BODY ECU - CAN NO. 3 J/C) |
Disconnect the main body ECU connector E8 from the main body ECU.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O33-1 (CANH) - E10-16 (BAT)
Ignition switch off
6 kΩ or higher
O33-2 (CANL) - E10-16 (BAT)
Ignition switch off
6 kΩ or higher
|
|
||||
| OK | ||
| ||
| 14. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CAN NO. 3 J/C WIRE) |
Disconnect CAN MS bus main wire connector O33 from the CAN No. 3 J/C.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O33-1 (CANH) - E10-4 (CG)
Ignition switch off
200 Ω or higher
O33-2 (CANL) - E10-4 (CG)
Ignition switch off
200 Ω or higher
|
|
||||
| OK | |
| 15. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (CLEARANCE WARNING ECU - CAN NO. 3 J/C) |
Reconnect CAN MS bus main wire connector O33 to the CAN No. 3 J/C.

Disconnect clearance warning ECU branch wire connector O32 from the CAN No. 3 J/C.
Disconnect connector O30 from the clearance warning ECU.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O32-1 (CANH) - E10-4 (CG)
Ignition switch off
200 Ω or higher
O32-2 (CANL) - E10-4 (CG)
Ignition switch off
200 Ω or higher
|
|
||||
| OK | ||
| ||
| 16. CHECK FOR SHORT TO GND IN CAN MS BUS WIRE (MAIN BODY ECU - CAN NO. 3 J/C) |
Disconnect the main body ECU connector E8 from the main body ECU.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Value
O33-1 (CANH) - E10-4 (CG)
Ignition switch off
200 Ω or higher
O33-2 (CANL) - E10-4 (CG)
Ignition switch off
200 Ω or higher
|
|
||||
| OK | ||
| ||
