2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

U1002 Lost Communication with Gateway Module

Diagnostic trouble codes · Vehicles built from Jun 2009

DESCRIPTION

  1. The gateway ECU will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to the CAN No. 2 bus.
  2. When the gateway ECU receives response signals from the ECUs connected to the CAN No. 2 bus, the gateway ECU recognizes and memorizes that the ECUs are connected to the CAN No. 2 bus. Based on this memorized data, the gateway ECU monitors for malfunctions in the ECUs connected to the CAN No. 2 bus when communicating with those ECUs. If the gateway ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN No. 2 bus, the gateway ECU determines that a malfunction exists.
DTC No.
DTC Detection Condition
Trouble Area
U1002
Gateway ECU cannot receive signals from all ECUs that have been memorized as those connected to the CAN No. 2 bus.
  1. Open or short in CAN No. 2 bus main wire or connector
  2. Open or short in CAN No. 2 bus branch wire or connector
  3. Gateway ECU
  4. CAN No. 2 J/C

WIRING DIAGRAM

C142752E02

INSPECTION PROCEDURE

NOTICE:
  1. Turn the engine switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
  2. After the engine switch is turned off, check that the key reminder warning system and lighting system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the engine switch, any other switches, or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the engine switch, any switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below will help to determine the cause of the malfunction.


1. CHECK CAN NO. 2 BUS WIRE

  1. C142741E02
    Turn the engine switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Result:
    Tester Connection
    Condition
    Specified Value
    Proceed to
    E70-13 (CA2H) - E70-12 (CA2L)
    Engine switch off
    54 to 69 Ω
    A
    E70-13 (CA2H) - E70-12 (CA2L)
    Engine switch off
    70 Ω or higher
    B
    E70-13 (CA2H) - E70-12 (CA2L)
    Engine switch off
    Less than 54 Ω
    C



B
Go to step 5

C
Go to step 7
A


2. CHECK FOR SHORT TO GND IN CAN NO. 2 BUS WIRE

  1. C144942E02
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E70-13 (CA2H) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    E70-12 (CA2L) - E10-4 (CG)
    Engine switch off
    200 Ω or higher



NG
Go to step 14
OK


3. CHECK FOR SHORT TO B+ IN CAN NO. 2 BUS WIRE
  1. Disconnect the cable from the negative (-) battery terminal.

  1. C144942E01
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E70-13 (CA2H) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E70-12 (CA2L) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher



NG
Go to step 11
OK


4. CHECK FOR OPEN IN CAN NO. 2 BUS BRANCH WIRE
  1. Check the AFS ECU branch wire and power source circuit (Click here).

Result:
Result
Proceed to
OK
A
NG
B



B
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH WIRE OR CONNECTOR
A

REPLACE GATEWAY ECU

5. CHECK FOR OPEN IN CAN NO. 2 BUS MAIN WIRE (GATEWAY ECU - CAN NO. 2 J/C)
  1. Disconnect the gateway ECU connector.

  1. C142190E08
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E70-13 (CA2H) - E70-12 (CA2L)
    Engine switch off
    108 to 132 Ω



NG
Go to step 6
OK

REPLACE GATEWAY ECU

6. CHECK FOR OPEN IN CAN NO. 2 BUS MAIN WIRE (CAN NO. 2 J/C)
  1. Reconnect the gateway ECU connector.

  1. C142239E02
    Disconnect CAN No. 2 bus main wire connector E79 from the CAN No. 2 J/C.

    HINT:
    E79 connector color: White

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E79-1 (CANH) - E79-2 (CANL)
    Engine switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (GATEWAY ECU - CAN NO. 2 J/C)
OK

REPLACE CAN NO. 2 J/C

7. CHECK FOR SHORT IN CAN NO. 2 BUS WIRE (CAN NO. 2 J/C WIRE)
  1. Disconnect the gateway ECU connector.

  1. C142190E08
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E70-13 (CA2H) - E70-12 (CA2L)
    Engine switch off
    108 to 132 Ω



NG
REPLACE GATEWAY ECU
OK


8. CHECK FOR SHORT IN CAN NO. 2 BUS WIRE (CAN NO. 2 J/C WIRE)
  1. Reconnect the gateway ECU connector.

  1. C142239E02
    Disconnect CAN No. 2 bus main wire connector E79 from the CAN No. 2 J/C.

    HINT:
    E79 connector color: White

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E79-1 (CANH) - E79-2 (CANL)
    Engine switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (GATEWAY ECU - CAN NO. 2 J/C)
OK


9. CHECK FOR SHORT IN CAN NO. 2 BUS WIRE (AFS ECU BRANCH WIRE)
  1. Reconnect CAN No. 2 bus main wire connector E79 to the CAN No. 2 J/C.

  1. C142742E01
    Disconnect AFS ECU branch wire connector E80 from the CAN No. 2 J/C.

    HINT:
    E80 connector color: Black

  1. C142741E02
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E70-13 (CA2H) - E70-12 (CA2L)
    Engine switch off
    54 to 69 Ω



NG
REPLACE CAN NO. 2 J/C
OK


10. CHECK FOR SHORT IN CAN NO. 2 BUS WIRE (AFS ECU)
  1. Reconnect AFS ECU branch wire connector E80 to the CAN No. 2 J/C.

  1. E133227E05
    Disconnect the AFS ECU wire harness connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    A61-12 (MPX1) - A61-13 (MPX2)
    Engine switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN NO. 2 BUS BRANCH WIRE OR CONNECTOR (AFS ECU BRANCH WIRE)
OK

REPLACE AFS ECU

11. CHECK FOR SHORT TO B+ IN CAN NO. 2 BUS WIRE (GATEWAY ECU)

  1. C144943E01
    Disconnect gateway ECU connector E70.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E70-13 (CA2H) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E70-12 (CA2L) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher



NG
Go to step 12
OK

REPLACE GATEWAY ECU

12. CHECK FOR SHORT TO B+ IN CAN NO. 2 BUS WIRE (CAN NO. 2 J/C)
  1. Reconnect gateway ECU connector E70.

  1. C142242E03
    Disconnect CAN No. 2 bus main wire connector E79 from CAN No. 2 J/C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E79-1 (CANH) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E79-2 (CANL) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (GATEWAY ECU - CAN NO. 2 J/C)
OK


13. CHECK FOR SHORT TO B+ IN CAN NO. 2 BUS WIRE (AFS ECU BRANCH WIRE)
  1. Disconnect AFS ECU connector A61.

  1. C152840E01
    Disconnect AFS ECU branch wire connector E80 from the CAN No. 2 J/C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E80-1 (CANH) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E80-2 (CANL) - E10-16 (BAT)
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN NO. 2 BUS BRANCH WIRE OR CONNECTOR (AFS ECU BRANCH WIRE)
OK

REPLACE AFS ECU

14. CHECK FOR SHORT TO GND IN CAN NO. 2 BUS WIRE (GATEWAY ECU)
  1. Disconnect gateway ECU connector E70.

  1. C144943E02
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E70-13 (CA2H) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    E70-12 (CA2L) - E10-4 (CG)
    Engine switch off
    200 Ω or higher



NG
Go to step 15
OK

REPLACE GATEWAY ECU

15. CHECK FOR SHORT TO GND IN CAN NO. 2 BUS WIRE (CAN NO. 2 J/C)
  1. Reconnect gateway ECU connector E70.

  1. C142242E04
    Disconnect CAN No. 2 bus main wire connector E79 from the CAN No. 2 J/C.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E79-1 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    E79-2 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher



NG
REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (GATEWAY ECU - CAN NO. 2 J/C)
OK


16. CHECK FOR SHORT TO GND IN CAN NO. 2 BUS WIRE (AFS ECU BRANCH WIRE)
  1. Disconnect AFS ECU connector A61.

  1. C152840E02
    Disconnect AFS ECU branch wire connector E80 from the CAN No. 2 J/C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E80-1 (CANH) - E10-4 (CG)
    Engine switch off
    200 Ω or higher
    E80-2 (CANL) - E10-4 (CG)
    Engine switch off
    200 Ω or higher



NG
REPAIR OR REPLACE CAN NO. 2 BUS BRANCH WIRE OR CONNECTOR (AFS ECU BRANCH WIRE)
OK

REPLACE AFS ECU


← U0182 Lost Communication with AFS ECU (from Jun 2009)Skid Control ECU Communication Stop Mode (from Oct 2006) →