2006-2011 Camry Aurion · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Oct 2006


1. REMOVE NO. 2 BREATHER PLUG

  1. C134951
    Using a screwdriver, remove the breather plug hose from the transaxle case.

  1. C134952E01
    Using a screwdriver, remove the breather plug from the breather plug hose.

  1. Using a screwdriver, remove the O-ring from the breather plug.

  1. Using a screwdriver, remove the breather plug cap from the breather plug hose.


2. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C136685
    Remove the nut, washer, and control shaft lever from the control shaft.

  1. C136686
    Remove the 2 bolts and the park/neutral position switch assembly from the transaxle case.

    NOTICE:
    Before removing the park/neutral position switch, remove any dirt or rust on the installation portion of the control shaft. Be sure to remove the switch straight along the shaft while being careful not to deform the plate spring that supports the shaft. If the plate spring is deformed, the park/neutral position switch cannot be reinstalled correctly.


3. REMOVE OIL COOLER TUBE UNION (OUTLET OIL COOLER UNION)

  1. C134956
    Remove the oil cooler tube union (outlet oil cooler union) from the transaxle case.

  1. Remove the O-ring from the oil cooler tube union (outlet oil cooler union).


4. REMOVE OIL COOLER TUBE UNION (INLET OIL COOLER UNION)

  1. C134957
    Loosen the nut while holding the oil cooler tube union (inlet oil cooler union).

  1. Remove the oil cooler tube union (inlet oil cooler union) from the transaxle case.

  1. Remove the O-ring from the oil cooler tube union (inlet oil cooler union).


5. REMOVE NO. 1 TRANSAXLE CASE PLUG

  1. C134958
    Remove the 3 No. 1 transaxle case plugs from the transaxle case.

  1. Using a screwdriver, remove the 3 O-rings from the 3 No. 1 transaxle case plugs.

  1. C134959
    Using a hexagon wrench (6 mm), remove the 3 hexagon bolts from the transaxle housing.

  1. Remove the 3 gaskets from the 3 hexagon bolts.


6. SECURE AUTOMATIC TRANSAXLE ASSEMBLY

  1. C136444
    Secure the transaxle assembly on wooden blocks.


7. REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

  1. C134961
    Using a hexagon wrench (6 mm), remove the overflow plug from the automatic transaxle oil pan sub-assembly.

  1. Remove the gasket from the overflow plug.

  1. C141531
    Using a hexagon wrench (6 mm), remove the No. 1 oil filler tube from the automatic transaxle assembly.

  1. C134962
    Remove the 18 bolts, automatic transaxle oil pan sub-assembly, and gasket from the automatic transaxle assembly.

  1. C134963E02
    Remove the 2 magnets from the automatic transaxle oil pan sub-assembly.


8. INSPECT TRANSMISSION OIL CLEANER MAGNET

  1. C138722
    Use the removed magnets to collect any steel chips. Examine the chips and particles in the pan and on the magnets to determine what type of wear has occurred in the transaxle:

    Result:
    Steel (magnetic):
    Bearing, gear and plate wear
    Brass (non-magnetic):
    Bearing wear


9. REMOVE VALVE BODY OIL STRAINER ASSEMBLY

  1. C136687
    Remove the 2 bolts and oil strainer assembly from the valve body assembly.

  1. C136688
    Remove the O-ring from the oil strainer assembly.


10. REMOVE TRANSMISSION VALVE BODY ASSEMBLY

  1. C136689
    Remove the 11 bolts and valve body assembly from the transaxle case.

    NOTICE:
    When removing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and the transaxle case to interfere with each other.


11. REMOVE TRANSAXLE CASE GASKET

  1. C136429
    Remove the 2 gaskets from the transaxle case.


12. INSPECT INPUT SHAFT SUB-ASSEMBLY

  1. C136696
    Using a dial indicator, measure the input shaft end play.

    End play:
    0.012 to 1.250 mm (0.0005 to 0.0492 in.)


13. REMOVE TRANSAXLE REAR COVER SUB-ASSEMBLY

  1. C136430
    Remove the refill plug from the transaxle rear cover.

  1. Remove the gasket from the refill plug.

  1. C134960
    Remove the 2 No. 1 automatic transaxle case plugs from the transaxle rear cover.

  1. Using a screwdriver, remove the 2 O-rings from the 2 No. 1 automatic transaxle case plugs.

  1. C136431E02
    Remove the 14 bolts from the transaxle rear cover.

  1. Using a brass bar and hammer, tap on the circumference of the rear transaxle cover to remove the transaxle rear cover from the transaxle case.

  1. C136432
    Using a screwdriver, remove the 3 O-rings from the transaxle case.

  1. C136440E01
    Using a screwdriver, remove the 2 oil seal rings from the transaxle rear cover.

  1. Remove the thrust needle roller bearing and thrust needle roller race from the transaxle rear cover.

  1. C136443
    Using a "TORX" wrench (T30), remove the 2 "TORX" screws and transaxle rear cover plate from the transaxle rear cover.

  1. C136690E01
    Using SST, remove the needle roller bearing from the transaxle rear cover.
    SST
    09319-60020  


14. REMOVE DIRECT MULTIPLE DISC CLUTCH ASSEMBLY

  1. C136442
    Remove the direct multiple disc clutch assembly from the transaxle case.

  1. Remove the thrust needle roller bearing from the direct multiple disc clutch assembly.


15. REMOVE DIRECT MULTIPLE DISC CLUTCH SNAP RING

  1. C136433
    Using 2 screwdrivers, remove the snap ring from the direct multiple disc clutch assembly.

  1. C136434
    Remove the No. 2 direct clutch piston from the direct multiple disc clutch assembly.

  1. C136428E01
    Using a screwdriver, remove the intermediate shaft oil seal from the direct multiple disc clutch assembly.

  1. Using a screwdriver, remove the O-ring from the direct multiple disc clutch assembly.


16. REMOVE NO. 2 DIRECT MULTIPLE DISC CLUTCH FLANGE

  1. C136435E01
    Remove the flange, 3 clutch discs and 3 clutch plates from the direct multiple disc clutch assembly.


17. INSPECT NO. 2 CLUTCH DISC

  1. C138267
    Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.

    NOTICE:
    If the linings of the discs are peeled off or discolored, or even if a part of the groove is damaged, replace all discs.


18. REMOVE REAR PLANETARY SUN GEAR ASSEMBLY

  1. C136436
    Using a snap ring expander, remove the snap ring from the direct multiple disc clutch assembly.

  1. C136437
    Remove the rear planetary sun gear from the direct multiple disc clutch assembly.

  1. C136438E01
    Remove the thrust needle roller bearing and thrust needle roller race from the direct multiple disc clutch assembly.


19. INSPECT REAR PLANETARY SUN GEAR ASSEMBLY

  1. C138266
    Using a dial indicator, measure the inside diameter of the bushing of the rear planetary sun gear sub-assembly.

    Standard inside diameter:
    25.580 to 25.601 mm (1.0071 to 1.0079 in.)

    Maximum inside diameter:
    25.601 mm (1.0079 in.)

    If the inside diameter is greater than the maximum, replace the rear planetary sun gear assembly.


20. REMOVE NO. 1 DIRECT MULTIPLE DISC CLUTCH FLANGE

  1. C136445
    Using 2 screwdrivers, remove the 2 snap rings from the direct multiple disc clutch assembly.

  1. C136446E02
    Remove the flange, 4 clutch discs, and 4 clutch plates from the direct multiple disc clutch assembly.


21. INSPECT NO. 1 CLUTCH DISC

  1. C138265
    Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.

    NOTICE:
    If the linings of the discs are peeled off or discolored, or even if a part of the groove is damaged, replace all discs.


22. REMOVE TRANSAXLE HOUSING

  1. C136447
    Remove the 20 bolts from the transaxle housing.

  1. Using a brass bar and hammer, tap on the circumference of the transaxle housing to remove the transaxle housing from the transaxle case.


23. REMOVE COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING OUTER RACE

  1. C136448E01
    Using SST, remove the counter driven gear front tapered roller bearing outer race and shim from the transaxle housing.
    SST
    09308-00010  


24. REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE

  1. C136449
    Remove the bolt, clamp, and differential gear lube apply tube from the transaxle housing.


25. REMOVE FRONT OIL PUMP AND GEAR BODY SUB-ASSEMBLY

  1. C136450
    Remove the 7 bolts and oil pump from the transaxle case.

  1. Remove the O-ring from the oil pump assembly.

  1. C138729E01
    Remove the thrust needle roller bearing and thrust needle roller race from the carrier lock nut.

  1. Remove the O-ring from the transaxle case.


26. REMOVE NO. 3 BRAKE DISC

  1. C162510E01
    Using a screwdriver, remove the snap ring from the oil pump assembly.

  1. C136452E01
    Remove the 2 brake flanges, 3 brake discs, and 2 brake plates from the oil pump assembly.


27. INSPECT NO. 3 BRAKE DISC

  1. C138255
    Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.

    NOTICE:
    If the linings of the discs are peeled off or discolored, or even if a part of the groove is damaged, replace all discs.


28. REMOVE UNDERDRIVE PLANETARY GEAR ASSEMBLY

  1. C136458
    Remove the underdrive planetary gear assembly from the oil pump assembly.


29. REMOVE NO. 3 BRAKE HUB

  1. C136454
    Remove the No. 3 brake hub from the underdrive planetary gear assembly.

  1. C136455E01
    Remove the thrust needle roller bearing and thrust needle roller race from the underdrive planetary gear assembly.


30. REMOVE UNDERDRIVE PLANETARY RING GEAR

  1. C136456
    Using needle-nose pliers, remove the snap ring from the underdrive planetary ring gear.

  1. Remove the underdrive planetary ring gear from the underdrive planetary gear assembly.


31. REMOVE PLANETARY SUN GEAR SUB-ASSEMBLY

  1. C136457
    While expanding the snap ring with snap ring pliers, remove the front planetary sun gear from the underdrive planetary gear assembly.

  1. Remove the snap ring from the underdrive planetary gear assembly.


32. INSPECT UNDERDRIVE PLANETARY GEAR ASSEMBLY

  1. C138260
    Using a feeler gauge, measure the clearance between the underdrive planetary gear and the pinion gear at 4 points.

    Standard clearance:
    0.18 to 0.54 mm (0.0071 to 0.0213 in.)

    If the clearance is greater than the standard clearance, replace the underdrive planetary gear.


33. INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY

  1. C138259
    Using a dial indicator, measure the inside diameter of the bushings of the planetary sun gear.

    Standard inside diameter:
    25.525 to 25.546 mm (1.0049 to 1.0057 in.)

    Maximum inside diameter:
    25.546 mm (1.0057 in.)

    If the inside diameter is greater than the maximum, replace the planetary sun gear.


34. REMOVE INPUT SHAFT SUB-ASSEMBLY

  1. C136459
    Remove the input shaft from the oil pump assembly.

  1. C136460E01
    Remove the thrust needle roller bearing and thrust needle roller race from the input shaft.

  1. Using a screwdriver, remove the 3 input shaft oil seal rings from the input shaft.


35. REMOVE UNDERDRIVE PLANETARY SUN GEAR

  1. C136461
    Remove the underdrive planetary sun gear from the oil pump assembly.

  1. Remove the thrust needle roller bearing from the oil pump assembly.


36. REMOVE NO. 1 BRAKE DISC

  1. C153477
    Using a screwdriver, remove the 2 snap rings and brake snap ring stopper from the oil pump assembly.

  1. C136463E01
    Remove the flange, 4 brake discs, and 4 brake plates from the oil pump assembly.


37. INSPECT NO. 1 BRAKE DISC

  1. C138255
    Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.

    NOTICE:
    If the linings of the discs are peeled off or discolored, or even if a part of the groove is damaged, replace all discs.


38. REMOVE 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

  1. C136464
    Remove the 3 2nd brake piston return springs from the oil pump assembly.


39. INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

  1. C138254
    Using vernier calipers, measure the free length of the 3 2nd brake piston return springs including the spring seats.

    Standard free length:
    23.85 mm (0.9390 in.)

    If the free length is shorter than the standard free length, replace the 2nd brake piston return spring.


40. REMOVE NO. 1 BRAKE PISTON

  1. C136465
    Holding the oil pump assembly by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil pump assembly to remove the No. 1 brake piston.

  1. C136466E01
    Using a screwdriver, remove the 2 O-rings from the No. 1 brake piston.


41. REMOVE FRONT DIFFERENTIAL CASE

  1. C136467
    Remove the differential case sub-assembly from the transaxle case.


42. REMOVE COUNTER DRIVE GEAR NUT

  1. C136698E01
    Using SST and a hammer, unstake the nut.
    SST
    09930-00010  

  1. C136700E01
    Turn the manual valve lever 2 notches counterclockwise to set it to the P position as shown in the illustration.

  1. C136468E01
    Using SST, remove the nut from the planetary gear assembly.
    SST
    09387-00130  


43. REMOVE COUNTER DRIVEN GEAR

  1. C136699E01
    Turn the manual valve lever 2 notches clockwise to set it to the N position as shown in the illustration.

  1. C136469
    Remove the counter driven gear sub-assembly from the transaxle case.


44. REMOVE COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING

  1. C136470E01
    Using SST, remove the counter driven gear front tapered roller bearing from the counter driven gear sub-assembly.
    SST
    09950-00020  
    09950-00030  
    09950-60010   (09951-00400)


45. REMOVE COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING

  1. C138720E01
    Using SST, remove the counter driven gear rear tapered roller bearing and differential drive pinion from the counter driven gear.
    SST
    09950-40011   (09951-04010, 09952-04010, 09954-04010, 09953-04020, 09955-04071, 09957-04010, 09958-04011)
    09950-60010   (09951-00320)


46. REMOVE PAWL SHAFT CLAMP

  1. C136472
    Remove the bolt and pawl shaft clamp from the transaxle case.


47. REMOVE PAWL STOPPER PLATE

  1. C136473
    Remove the 2 bolts and pawl stopper plate from the transaxle case.


48. REMOVE PARKING LOCK SLEEVE

  1. C136474
    Remove the parking lock sleeve from the transaxle case.


49. REMOVE PARKING LOCK PAWL

  1. C136475
    Remove the spring, parking lock pawl pin, parking lock pawl shaft, and parking lock pawl from the transaxle case.


50. REMOVE COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING OUTER RACE

  1. C136476E01
    Using SST, remove the counter driven gear rear tapered roller bearing outer race from the transaxle case.
    SST
    09308-00010  


51. REMOVE ONE-WAY CLUTCH ASSEMBLY

  1. C141525
    Using a screwdriver, remove the snap ring from the transaxle case.

  1. C141526
    Remove the one-way clutch assembly with the planetary ring gear from the transaxle case.

  1. Remove the thrust needle roller bearing from the transaxle case.


52. INSPECT ONE-WAY CLUTCH ASSEMBLY

  1. C138723
    Temporarily install the one-way clutch assembly to the planetary ring gear.

  1. Rotate the one-way clutch assembly to check the rotating direction for lock or free operation.
    If the one-way clutch assembly does not operate normally, replace it.


53. REMOVE PLANETARY RING GEAR

  1. C136479
    Remove the planetary ring gear from the one-way clutch assembly.


54. REMOVE PLANETARY RING GEAR FLANGE

  1. C136480
    Using a screwdriver, remove the snap ring from the planetary ring gear.

  1. Remove the planetary ring gear flange from the planetary ring gear.


55. REMOVE NO. 2 BRAKE DISC

  1. C141524
    Using a screwdriver, remove the snap ring from the transaxle case.

  1. C136483E01
    Remove the brake flange, 5 brake discs, and 5 brake plates from the transaxle case.


56. INSPECT NO. 2 BRAKE DISC

  1. C137438
    Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.

    NOTICE:
    If the linings of the discs are peeled off or discolored, or even if a part of the groove is damaged, replace all discs.


57. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. C136482
    Using a screwdriver, remove the snap ring from the transaxle case.

  1. C136484
    Remove the 1st and reverse brake return spring from the transaxle case.


58. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

C141533
  1. Using vernier calipers, measure the free length of the 1st and reverse brake return spring together with the spring seat.

    Standard free length:
    15.79 mm (0.6217 in.)

    If the free length is shorter than the standard free length, replace the 1st and reverse brake return spring.


59. REMOVE NO. 2 BRAKE PISTON

  1. C136485
    Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the ATF hole to remove the No. 2 brake piston assembly from the transaxle case.

  1. C136673E01
    Using a screwdriver, remove the 2 O-rings from the No. 2 brake piston.


60. REMOVE FRONT PLANETARY GEAR ASSEMBLY

  1. C136674E01
    Using SST and a press, remove the planetary gear assembly from the transaxle case.
    SST
    09950-60010   (09951-00580)
    09950-70010   (09951-07100)


61. REMOVE COUNTER DRIVE GEAR

  1. C136697E01
    Using SST and a press, remove the counter drive gear and bearing inner race (rear side) from the transaxle case.
    SST
    09950-60020   (09951-00710)
    09950-70010   (09951-07100)

  1. C136676
    As shown in the illustration, tighten the 3 bolts evenly and leave a clearance of approximately 20.0 mm (0.787 in.) between the counter drive gear and inner race.

  1. C136677E01
    Using SST, remove the bearing inner race (front side) from the counter drive gear.
    SST
    09950-00020  
    09950-00030  
    09950-60020   (09951-00710)


62. REMOVE NO. 3 BRAKE PISTON

  1. C136678
    Using a screwdriver, remove the snap ring from the transaxle case.

  1. C136679
    Remove the brake piston return spring from the transaxle case.

  1. Remove the No. 3 brake piston from the transaxle case.


63. REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY

  1. C134953
    Remove the bolt, cover, and manual detent spring sub-assembly from the transaxle case.


64. REMOVE PARKING LOCK ROD SUB-ASSEMBLY

  1. C136683
    Remove the parking lock rod sub-assembly from the parking lock lever sub-assembly.

    HINT:
    Align the slot with the notches on the parking lock lever sub-assembly to remove the parking lock rod sub-assembly.


65. REMOVE MANUAL VALVE LEVER SHAFT

  1. C136680
    Using needle-nose pliers, remove the manual valve lever shaft retainer spring from the transaxle case.

  1. C136701
    Using a screwdriver, slide the spacer of the manual valve lever sub-assembly.

  1. C137417
    Using a pin punch (3 mm) and hammer, drive out the slotted spring pin from the manual valve lever sub-assembly.

    HINT:
    Slowly drive out the pin so that it will not fall into the transaxle case.

  1. C137418
    Using a screwdriver, slide the spacer of the parking lock lever sub-assembly.

  1. C136702
    Using a pin punch (3 mm) and hammer, drive out the slotted spring pin from the parking lock lever sub-assembly.

    HINT:
    Slowly drive out the pin so that it will not fall into the transaxle case.

  1. C137428
    Remove the manual valve lever shaft, manual valve lever sub-assembly, parking lock lever sub-assembly and 2 spacers from the transaxle case.


66. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

  1. C136684
    Using a screwdriver, remove the manual valve lever shaft oil seal from the transaxle case.

← COMPONENTS (from Oct 2006)INSPECTION (from Oct 2006) →