2006-2011 Camry Aurion · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Oct 2006


1. REMOVE REAR QUARTER PANEL MUDGUARD SUB-ASSEMBLY LH (w/o Rear Lower Spoiler)

  1. B137209
    Remove the 3 screws and rear quarter panel mudguard sub-assembly LH.


2. REMOVE REAR QUARTER PANEL MUDGUARD SUB-ASSEMBLY RH (w/o Rear Lower Spoiler)

HINT:
Use the same procedure for the RH side and LH side.


3. REMOVE REAR FLOOR BOARD (w/ Rear Lower Spoiler)

  1. B138885E01
    Remove the 4 screws, 2 clips, 3 nuts and rear floor board.


4. REMOVE REAR BUMPER ASSEMBLY (w/o Clearance Sonar System)

  1. without Rear Lower Spoiler:

    1. B149447E01
      Put protective tape around the rear bumper assembly.

    2. B149448
      Using a screwdriver, open the 2 rear bumper plates.

      HINT:
      Tape the screwdriver tip before use.

    3. B149450
      Remove the 6 screws and 2 clips.

    4. B149451
      Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration.

      HINT:
      Use the same procedure for the RH side and LH side.

    5. Remove the rear bumper assembly.

  1. with Rear Lower Spoiler:

    1. B160683E01
      Put protective tape around the rear bumper assembly.

    2. B160684
      Using a screwdriver, open the 2 rear bumper plates.

      HINT:
      Tape the screwdriver tip before use.

    3. B160685
      Remove the 6 screws.

    4. B160687
      Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration.

      HINT:
      Use the same procedure for the RH side and LH side.

    5. Remove the rear bumper assembly.


5. REMOVE LUGGAGE COMPARTMENT FLOOR MAT (w/ Clearance Sonar System)

6. REMOVE SPARE WHEEL COVER CLAMP (w/ Clearance Sonar System)

7. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Clearance Sonar System)

8. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (w/ Clearance Sonar System)

  1. B136879
    Remove the 2 screws and the 2 No. 1 luggage compartment trim hooks.


9. REMOVE REAR FLOOR FINISH PLATE (w/ Clearance Sonar System)

  1. B136852
    Disengage the 7 clips and remove the rear floor finish plate.


10. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER RH (w/ Clearance Sonar System)

  1. B136855
    Remove the 2 clips and the luggage compartment inner trim cover RH.


11. REMOVE REAR BUMPER ASSEMBLY (w/ Clearance Sonar System)

  1. without Rear Lower Spoiler:

    1. B149446
      Disconnect the connector.

    2. Disengage the grommet.

    3. B149447E01
      Put protective tape around the rear bumper assembly.

    4. B149448
      Using a screwdriver, open the 2 rear bumper plates.

      HINT:
      Tape the screwdriver tip before use.

    5. B149450
      Remove the 6 screws and 2 clips.

    6. B149451
      Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration.

      HINT:
      Use the same procedure for the RH side and LH side.

    7. Disengage each No. 2 luggage room wire clamp from the rear bumper reinforcement sub-assembly.

    8. Remove the rear bumper assembly.

  1. with Rear Lower Spoiler:

    1. B149446
      Disconnect the connector.

    2. Disengage the grommet.

    3. B160683E01
      Put protective tape around the rear bumper assembly.

    4. B160684
      Using a screwdriver, open the 2 rear bumper plates.

      HINT:
      Tape the screwdriver tip before use.

    5. B160685
      Remove the 6 screws.

    6. B160687
      Disengage the 12 claws and disconnect the rear bumper assembly as shown in the illustration.

      HINT:
      Use the same procedure for the RH side and LH side.

    7. Disengage each No. 2 luggage room wire clamp from the rear bumper reinforcement sub-assembly.

    8. Remove the rear bumper assembly.

← COMPONENTS (from Oct 2006)DISASSEMBLY (Oct 2006 – May 2009) →