2006-2011 Camry Aurion · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built from Jun 2006


1. INSTALL SEPARATE TYPE FRONT SEAT CUSHION PAD

  1. B140572E01
    Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 16 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


2. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

  1. B148649
    Engage the hooks and install the separate type front seat cushion cover with pad.


3. INSTALL FRONT SEAT INNER BELT ASSEMBLY

  1. B147690E01
    Install the front seat inner belt assembly with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

  1. B151307E01
    Connect the connectors and engage the 2 clamps.


4. INSTALL FRONT INNER SEAT CUSHION SHIELD

  1. B147731
    Engage the 3 claws.

  1. Install the front inner seat cushion shield with the screw.


5. INSTALL FRONT SEAT CUSHION SHIELD

  1. B147726
    Engage the 3 claws.

  1. Install the front seat cushion shield with the 2 screws.

  1. B147725
    Engage the 2 hooks.


6. INSTALL RECLINING ADJUSTER RELEASE HANDLE

  1. B147691
    Engage the claw to install the reclining adjuster release handle.


7. INSTALL FRONT SEAT ASSEMBLY
  1. Place the front passenger's seat assembly in the vehicle and align the adjuster pin with the hole on the vehicle side.

  1. Connect the connectors and clamp.

  1. Move the front passenger's seat assembly to the rearmost position by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. B147667
    Temporarily install the front seat track bracket with the 2 bolts.

  1. Move the front passenger's seat assembly fully forward by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. B147668
    Temporarily install the rear seat track bracket with the 2 bolts.

  1. Move the front passenger's seat assembly to the rearmost position by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. Fully tighten the 2 bolts on the front seat track bracket in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Move the front passenger's seat assembly fully forward by operating the slide handle.

    NOTICE:
    Check that the seat is locked.

  1. Fully tighten the 2 bolts on the rear seat track bracket in the order of the inner side bolt and then the outer side bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


8. INSTALL INNER SEAT TRACK BRACKET COVER

  1. B147666E01
    Slide the inner seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

  1. Push the inner seat track bracket cover to engage claw B.


9. INSTALL OUTER SEAT TRACK BRACKET COVER

  1. B147665E01
    Slide the outer seat track bracket cover along the seat rail toward the front of the vehicle. Engage claw A to the seat rail.

  1. Push the outer seat track bracket cover to engage claw B.


10. INSTALL FRONT SEAT HEADREST ASSEMBLY

11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

12. INSPECT SLIDE ADJUSTER LOCK
← INSPECTION (from Jun 2009)COMPONENTS (from Oct 2006) →