Install the dust cover to the parking brake shoe lever as shown in the illustration.
Using an air riveter or a hand riveter with a nose piece, install the boot retainer on the back plate with 2 new rivets.
HINT:
If the rivet cannot be cut, pull it once and cut it.
NOTICE:
Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.
Confirm that the rivets are seated properly against the boot retainer. Do not tilt the riveter when installing the rivet to the boot retainer. Do not leave any space between the rivet head and the boot retainer.
Do not leave any space between the boot retainer and the back plate. Firmly hold together the 2 items while installing the rivet.
3.
INSTALL DUST PLATE
Install the dust plate to the parking brake plate sub-assembly.
4.
INSTALL PARKING BRAKE SHOE HOLD PLATE
Install the parking brake shoe hold plate with a new parking brake shoe hold bolt.
Torque:
9.0 N*m{
92 kgf*cm
, 80 in.*lbf
}
5.
INSTALL ADJUSTMENT PAWL
Install the adjustment pawl.
6.
INSTALL NUT AND SCREW ADJUSTING ASSEMBLY
Apply high temperature grease to the inside of the back plate bore as shown in the illustration.
Install the nut and screw adjusting assembly, parking brake tappet and parking brake push rod.
7.
INSTALL PARKING BRAKE PLATE SUB-ASSEMBLY
8.
INSTALL REAR AXLE HUB & BEARING ASSEMBLY
Install the hub and bearing assembly with the 4 bolts.
Torque:
80 N*m{
816 kgf*cm
, 59 ft.*lbf
}
Connect the skid control sensor connector.
NOTICE:
Do not twist the sensor wire when connecting it.
9.
CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY
Turn and connect the No. 3 parking brake cable assembly.
Using a brass bar and a hammer, install the clip to the No. 3 parking brake cable assembly.
10.
INSTALL PARKING BRAKE SHOE ASSEMBLY
Install the parking brake shoe assembly as shown in the illustration.
NOTICE:
There should be no oil or grease on the friction surface of the lining and disc.
11.
INSPECT REAR AXLE HUB BEARING LOOSENESS
Using a dial indicator, check for looseness near the center of the axle hub.
Maximum:
0.05 mm (0.0020 in.)
NOTICE:
Ensure that the dial indicator is set perpendicular to the measurement surface.
If looseness exceeds the maximum, replace the axle hub assembly.
12.
INSPECT REAR AXLE HUB RUNOUT
Using a dial indicator, check for runout on the surface of the axle hub outside the hub bolt.
Maximum:
0.07 mm (0.0027 in.)
NOTICE:
Ensure that the dial indicator is set perpendicular to the measurement surface.
If runout exceeds the maximum, replace the axle hub assembly.
13.
INSTALL REAR DISC
Align the matchmarks and install the rear disc.
14.
ADJUST PARKING BRAKE SHOE CLEARANCE
Remove the rear brake caliper.
HINT:
Do not disconnect the flexible hose.
Do not remove the brake pads.
Do not allow the caliper to hang on the flexible hose. Always support the caliper.
Remove the disc rotor.
HINT:
If the disc rotor is difficult to remove, rotate the disc whilst pulling on the rotor.
If the disc jams, return the disc to its original position, turn the shoe adjuster in a clockwise direction to contact the brake and attempt to remove the disc again.
Measure the brake shoe diameter as shown in the illustration.
Standard diameter:
189.55 to 189.75 mm (7.463 to 7.470 in.)
If the shoe diameter is out of specification, adjust it by turning the nut as shown in the illustration.
The gap between the adjusting nut and screw must not exceed 5 mm (0.197 in.) as shown in the illustration. If the gap is set to this specification and the shoe diameter is less than specified, replace the parking brake shoe. If the lining thickness is less than 1.5 mm (0.059 in.) or exhibits uneven wear, replace the parking brake shoe.
Check for drag. Spin the rotor and ensure there is no drag from the parking brake shoe.
HINT:
If there is drag, apply and release the parking brake lever or parking brake pedal and retest. If drag is still present, remove the disc, remeasure and readjust the shoe diameter and centralize the shoe. Reassemble the disc and recheck for drag.