2006-2011 Camry Aurion · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009


1. INSTALL FRONT BRAKE FLEXIBLE HOSE (for LHD)

  1. C145053E02
    Connect the front brake flexible hose with the union bolt and a new gasket.

    Torque:
    29 N*m{ 300 kgf*cm , 21 ft.*lbf }

  1. Install the front brake flexible hose and the front speed sensor to the shock absorber with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    NOTICE:
    When installing the front brake flexible hose and the speed sensor, the bracket must face toward the exterior of the vehicle.

  1. Install the front brake flexible hose with a new clip.

    NOTICE:
    1. When installing the front brake flexible hose, face the identification mark toward the exterior of the vehicle and minimize twisting of the hose.
    2. Install the clip as far as it will go.

  1. Using SST, connect the brake line to the front brake flexible hose while holding the front brake flexible hose with a wrench.

    SST
    09023-00101  

    Torque:
    Without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    With SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    NOTICE:
    1. Do not bend or damage the brake line.
    2. Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.
    3. Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).
    4. This torque value is effective when SST is parallel to a torque wrench.


2. INSTALL FRONT BRAKE FLEXIBLE HOSE (for RHD)

  1. C144143E05
    Connect the front brake flexible hose with the union bolt and 2 new gaskets.

    Torque:
    29 N*m{ 300 kgf*cm , 21 ft.*lbf }

  1. Connect the front flexible hose and the speed sensor to the shock absorber with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    NOTICE:
    When installing the front brake flexible hose and the speed sensor, the bracket must face toward the exterior of the vehicle.

  1. Install the front brake flexible hose with a new clip.

    NOTICE:
    1. When installing the front brake flexible hose, face the identification mark toward the exterior of the vehicle and minimize twisting of the hose.
    2. Install the clip as far as it will go.

  1. Using SST, connect the brake line to the front brake flexible hose while holding the front brake flexible hose with a wrench.

    SST
    09023-00101  

    Torque:
    Without SST:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    With SST:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    NOTICE:
    1. Do not bend or damage the brake line.
    2. Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.
    3. Use a torque wrench with a fulcrum length of 250 mm ( 9.84 in.).
    4. This torque value is effective when SST is parallel to a torque wrench.


3. FILL RESERVOIR WITH BRAKE FLUID

  1. C132849
    Fill the reservoir with brake fluid.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3


4. BLEED BRAKE LINE

NOTICE:
Bleed the air from the brake line of the wheel farthest from the master cylinder.

  1. C132853
    Connect a vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (*3).

  1. C132852
    When fluid stops coming out, tighten the bleeder plug, then release the brake pedal (*4).

  1. Repeat (*3) and (*4) until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug completely.

    Torque:
    for LHD:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
    for RHD:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Repeat the above procedures for each wheel to bleed the air from the brake line.


5. INSPECT BRAKE FLUID LEVEL IN RESERVOIR

  1. C144901E01
    Check the fluid level.
    If brake fluid level is low, check for leakage and inspect the disc brake pad. If necessary, refill the reservoir with brake fluid after repair and replacement.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3


6. INSPECT FOR FLUID LEAK

7. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }

← INSTALLATION (Jun 2006 – Sep 2006)INSTALLATION (from Jun 2009) →