INSTALLATION
Removal / installation · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
| 1.
INSTALL SEPARATE TYPE FRONT SEAT CUSHION PAD |
 |
- Using hog ring pliers, install the separate type front seat cushion pad to the separate type front seat cushion cover with 14 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
| 2.
INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD |
 |
- Engage the hooks.
- Engage the 4 hooks.
Connect the connector.
| 3.
INSTALL FRONT POWER SEAT SWITCH |
 |
- Install the front power seat switch with the 3 screws.
Connect the connector.
| 4.
INSTALL FRONT SEAT INNER BELT ASSEMBLY |
 |
- Install the front seat inner belt assembly with the nut.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- NOTICE:
- Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
- Connect the connectors and engage the 2 clamps.
| 5.
INSTALL FRONT INNER SEAT CUSHION SHIELD |
 |
- Engage the 3 claws.
Install the front inner seat cushion shield with the screw.
| 6.
INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY |
 |
- Connect the connector.
Engage the 2 claws.
Install the front seat cushion shield assembly with the 5 screws.
- Install the 2 rubber bands on the backside of the front seatback board sub-assembly.
| 7.
INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB |
 |
- Install the slide and vertical power seat switch knob.
| 8.
INSTALL RECLINING POWER SEAT SWITCH KNOB |
 |
- Install the reclining power seat switch knob.
| 9.
INSTALL FRONT SEAT ASSEMBLY |
 |
Place the seat in the cabin.
Connect the connectors under the seat.
Connect the cable to the negative (-) battery terminal.
Move the front passenger's seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.
- Temporarily install the front side of the front passenger's seat assembly with the 2 bolts.
Move the front passenger's seat assembly fully forward by operating the slide and vertical power seat switch knob.
- Temporarily install the rear side of the front passenger's seat assembly with the 2 bolts.
Move the front passenger's seat assembly to the rearmost position by operating the slide and vertical power seat switch knob.
Fully tighten the 2 bolts on the front side of the front passenger's seat assembly in the order of the inner side bolt and then the outer side bolt.
-
Torque:
- 37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
Move the front passenger's seat assembly fully forward by operating the slide and vertical power seat switch knob.
Fully tighten the 2 bolts on the rear side of the front passenger's seat assembly in the order of the inner side bolt and then the outer side bolt.
-
Torque:
- 37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
| 10.
INSTALL OUTER SEAT TRACK BRACKET COVER |
 |
- Engage the 4 claws and install the outer seat track bracket cover.
| 11.
INSTALL INNER SEAT TRACK BRACKET COVER |
 |
Engage the 4 claws and install the inner seat track bracket cover.
| 12.
INSTALL FRONT SEAT HEADREST ASSEMBLY |
|
| 13.
INSPECT SRS WARNING LIGHT (w/ Front Seat Side Airbag) |
 |
(Click here)
| 14.
INSPECT FRONT SEAT ASSEMBLY
|
 |
Inspect the power seat operation.