2006-2011 Camry Aurion · Service Manual COMMUNICATION SYSTEM

B2321 Driver Side Door ECU Communication Stop

Diagnostic trouble codes · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

This DTC is output when LIN communication between the power window regulator motor (Driver side) and main body ECU (Instrument panel junction block assembly) stops for more than 10 seconds.
DTC No.
DTC Detection Condition
Trouble Area
B2321
No communication between power window regulator motor (Driver side) and main body ECU (Instrument panel junction block assembly) for more than 10 seconds
  1. Power window regulator motor (Driver side)
  2. Main body ECU (Instrument panel junction block assembly)
  3. Wire harness or connector

WIRING DIAGRAM

B176995E20

INSPECTION PROCEDURE

NOTICE:
When using the intelligent tester with the ignition switch off to troubleshoot:
Connect the intelligent tester to the vehicle, and turn the courtesy switch on and off at 1.5-second intervals until communication between the tester and vehicle begins.


1. CLEAR DTC
  1. Delete the DTC (Click here).


NEXT


2. CHECK DTC OUTPUT
  1. Recheck for DTC (Click here).

    Result:
    Result
    Proceed to
    B2321 is not output
    A
    B2321 is output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - POWER WINDOW REGULATOR MOTOR)

  1. Disconnect the E8 and I5*1 or H10*2 connectors.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

    B178903E08

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    E8-10 (LIN2) - I5-9 (LIN)
    Always
    Below 1 Ω
    E8-10 (LIN2) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    E8-10 (LIN2) - H10-9 (LIN)
    Always
    Below 1 Ω
    E8-10 (LIN2) - Body ground
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E8-10 (LIN2) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR - BATTERY AND BODY GROUND)

  1. B164451E22
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    I5-1 (E) - Body ground
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    H10-1 (E) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    I5-2 (B) - Body ground
    Always
    11 to 14 V
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    H10-2 (B) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE POWER WINDOW REGULATOR MOTOR (DRIVER SIDE)
  1. Replace the power window regulator motor (Driver side) with a normally-functioning or a new one (Click here).

  1. Delete the DTC (Click here).


NEXT


6. CHECK DTC OUTPUT
  1. Recheck for DTC (Click here).

    Result:
    Result
    Proceed to
    B2321 is not output
    A
    B2321 is output
    B



B
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
A

END (POWER WINDOW REGULATOR MOTOR (DRIVER SIDE) IS DEFECTIVE)


← B2321 Driver Side Door ECU Communication Stop (Jun 2006 – Sep 2006)B2321 Driver Side Door ECU Communication Stop (from Jun 2009) →