SYSTEM DESCRIPTION
Troubleshooting · Vehicles built from Oct 2006
| GENERAL INFORMATION |
The Toyota Link system has been developed using some of the most advanced Global Positioning System (GPS), telecommunications technology and Global System for Mobile (GSM) communications available.
The Toyota Link system provides in-vehicle safety, security and information services by providing a two way, handsfree communication to the Toyota Link Call Centre. Toyota Link provides several services, such as:
In addition it will know if theft of the vehicle is attempted and can then track the vehicle. For a full list of services provided by Toyota Link, refer to the Toyota Link Owner's Manual or the Toyota Web site.
The link between the vehicle and the Toyota Link Call Centre uses GPS for vehicle location and tracking and the Australian digital mobile phone network to transmit and receive voice and SMS (Short Message Service) data.
If the vehicle is outside the network coverage area, the link to and from the vehicle will not be available and services cannot be provided.
Signal strength may be affected in locations like basement car parks or tunnels. However, in most cases, as the vehicle emerges from the obstruction or re-enters the digital phone network area the signal will be available again.
A vehicle equipped with the Toyota Link system will be delivered from the vehicle assembly plant to the retail outlet with the system in Pre-delivery mode.
During the pre-delivery service of the vehicle, the mayday ECU Pre-delivery mode must be changed to Service mode using the Toyota Link Diagnostic Tool.
In Service mode, limited service will be provided until the customer has signed the terms and conditions document and the customer has set up the system by pressing the Toyota Link button located on the roof console box assembly.
The Toyota Link operator will then disable the Service mode and the system will be fully operational.
The mayday ECU has a built-in diagnostic system that identifies system operational problems and alerts the driver by illuminating the red LED in the roof console box assembly. If the LED is continuously illuminated with the engine switch on (IG), the Toyota Link system will not be functional and the cause of the illuminated lamp should be checked as soon as possible.
- Mayday ECU:
Controls the system and initiates or receives calls from the Toyota Link call centre,
- GSM antenna,
- GPS antenna, and
- Roof console box assembly:
Incorporates the system operation buttons and is the interface between the vehicle and the Toyota Link call centre.
- remote door unlocking,
- connection to roadside assistance,
- low battery alert, and
- accident inquiry.
| PRINCIPLES OF OPERATION |
OPERATING MODES
The Toyota Link system has six operating modes:- Pre-delivery,
- Service,
- Active,
- Stand-by,
- Sleep, and
- Deep sleep.
Pre-Delivery Mode:
In pre-delivery mode the system is not operational. The vehicle will be delivered from the assembly plant to the dealer with the mayday ECU in Pre-delivery mode.
Before the vehicle is delivered to the customer, the Toyota Link system must be taken out of Pre-delivery mode using the diagnostic tool.
When in Pre-delivery mode the mayday ECU will only communicate with the diagnostic tool and only when the engine switch is on (IG).Service Mode:
When the vehicle is scheduled to be serviced, the Toyota Link system Service mode should be activated.
The customer may request the Toyota Link Call centre to remotely enable or disable Service mode.
A service technician can also activate or deactivate service mode with the diagnostic tool.
When the Service mode is activated the mayday ECU will ignore all button presses except for the Toyota Link button. In addition, the module will not transmit alert messages for un-authorised entry or low battery. However the module will transmit an airbag deployment alert, and the remote unlock function will still be active.
The unit will emit five beeps when the engine switch is on (IG) to alert the driver that it is in Service mode.Active Mode:
This is the normal Toyota Link operating mode. In this mode the Toyota Link system is fully functional making and receive calls, and transmitting data via the GSM network.
The current draw of the mayday ECU in this mode will be approximately 150 mA.Sleep Mode:
- Stand-by
- The mayday ECU will enter Stand-by mode two minutes after the engine switch is turned off and a door is opened and closed; or 30 minutes after the engine switch is turned off.
- In this mode the roof console box buttons will be inactive. The mayday ECU will wake from this mode if:
- any door is opened,
- the alarm is triggered,
- an unauthorised entry alert,
- an incoming message, or
- an ignition event.
- A progressively deeper sleep behaviour is adopted after eight hours in stand-by mode.
- Sleep:
- The mayday ECU will enter Sleep mode after eight hours of uninterrupted Stand-by mode time. In Sleep mode the mayday ECU only monitors the inputs required for it to be woken from Sleep mode.
- The system may be woken from Sleep mode by any of the following triggers:
- any door is opened,
- the alarm is triggered,
- an unauthorised entry alert,
- an incoming message, or
- an ignition event.
- In this mode the roof console box buttons are inactive and the mayday ECU will check the network for SMS messages two minutes out of every 17 minutes.
- Stand-by
Deep Sleep:
The mayday ECU enters a deep sleep behaviour 5.5 days after the engine switch has been turned off and no other activity has occurred.
The customer may also have the mayday ECU put into Deep Sleep mode by the Toyota Link Call Centre.
In this mode the roof console box buttons are inactive and the mayday ECU will check the network for SMS messages two minutes out of every 255 minutes.

- Pre-delivery,
ALERTS
The Toyota Link system has three alerts:- Airbag deployment alert,
- Low battery voltage alert, and
- Unauthorised entry alert.
Airbag Deployment Alert:
If the vehicle is involved in an accident where the airbags are activated, an Airbag Deployed Alert message will be transmitted to the Toyota Link Call Centre.
If the Toyota Link Call centre operator is unable to contact the driver via two-way voice communication in the vehicle, or if the driver cannot respond, the operator will hand the call over to the Police.
The Police may then contact the ambulance or other services.Low Battery Voltage Alert:
If the vehicle battery voltage falls below a preset voltage;- 11.6 V - 11.4V for longer than 30 minutes,
- 11.4 V - 11.0V for longer than 20 minutes,
- 11.0 V - 1.0V for longer than 90 seconds,
The low battery alert voltage is displayed in the Toyota Link Diagnostic Tool (TDT) Data List.- 11.6 V - 11.4V for longer than 30 minutes,
Unauthorised Entry Alert:
If the vehicle security system is triggered or when the vehicle battery voltage is below 1 V for longer than 60 seconds, the mayday ECU will transmit an Unauthorised Entry Alert message to the Toyota Link Call Centre.
The operator will then attempt to make contact with the vehicle occupant to validate them as the owner or an authorised user.
- Airbag deployment alert,
TOYOTA LINK REMOTE REQUESTS
Remote Unlocking:
On receiving a Remote Unlock message from the Toyota Link Call Centre, the mayday ECU will command the body ECU to unlock the doors.
The remote unlock command may take up to several hours to activate the door locks depending on the sleep state of the mayday ECU.- HINT:
- A remote unlock from the Toyota Link Call centre will not function while the diagnostic tool is accessing any module diagnostic information.
MAYDAY ECU

The mayday ECU located under the rear parcel tray and controls the operation of the Toyota Link system.
The ECU consists of a GPS and GSM engine. It monitors vehicle operating conditions via discrete inputs and controls system outputs.
The ECU also receives and transmits GSM information via the GSM antenna and receives GPS information via the GPS antenna. The ECU interfaces with other control modules in the vehicle.- NOTICE:
- If a new mayday ECU is installed into the vehicle, it must be registered with Toyota Link.
ROOF CONSOLE BOX ASSEMBLY
The roof console box assembly contains the mayday ECU button pad, microphone, volume control and the status LEDs.MAYDAY ECU BUTTON PAD
The mayday ECU button pad is a resistor encoded switch, which means that each button has a separate and different value resistor connected to it.
The ECU uses a voltage divider circuit to determine which button has been pressed. The ECU supplies a 12 V signal voltage to the roof console box connector Q16 terminal 9
Whenever a button is pressed, the corresponding switch is closed and the DATA circuit at the mayday ECU is connected to ground through a resistor, each switch having a different value resistor.
The ECU monitors the voltage on the DATA circuit which will change when any of the buttons are pressed.Emergency Button:
When the Emergency button is pressed, the voltage on the DATA circuit at the mayday ECU will be approximately 3.8 V. The ECU determines this voltage as an Emergency button press.
The mayday ECU will initiate a voice call to an operator at the Toyota Link call centre and then send an SMS message containing status and location data.
If the call cannot be connected, the ECU will immediately re-attempt to connect the call a second time.
If the second attempt also fails, the unit will wait for 60 seconds and make a third and final attempt.
If the emergency button is pressed while a Toyota Link call is in progress, the status of the call will be upgraded to an emergency call and the ECU will not be permitted to terminate the call by pressing the End Call button.
If the emergency button is pressed while the vehicle is outside GSM network range, the ECU will enter Emergency Call mode, where by the emergency call request will be retained. When contact is re-established with the GSM network, the emergency call will be placed immediately.Toyota Link Button:
When the Toyota Link button is pressed, the voltage on the DATA circuit at the mayday ECU will be approximately 2.3 V. The ECU determines this voltage as a Toyota Link Button press.
The mayday ECU will initiate a voice call to the call centre and then send an SMS message containing status and location data.
If the call can not be connected, the ECU will immediately re-attempt to connect the call a second time. If the second attempt also fails, the unit will wait for 60 seconds and make a third and final attempt.End Call Button:
When the End Call button is pressed, the voltage on the DATA circuit at the mayday ECU will be approximately 0.7 V. The mayday ECU determines this voltage as an End Call button press.
Pressing this button while a call is connected will disconnect the call. It will not disconnect a call while the call is ringing the Toyota Link Call Centre number.
It is not possible for the End Call button to disconnect an emergency call or a Toyota Link call that has been upgraded to an emergency call status.Volume Adjustment:
During the course of any voice call made to or from the Toyota Link Call Centre, the volume can be adjusted by using the Volume up / Volume down buttons located on the roof console box assembly.Microphone:
The active microphone in the roof console box assembly provides a means for voice communication to the vehicle occupants and the Toyota Link Call Centre.Status Indicator LEDs:
The red and green status indicator LEDs in the roof console box assembly indicate the current status of the Toyota Link system.
The mayday ECU activates the LEDs by switching a 12 V power supply to each LED ON or OFF. The brightness of the LEDs is controlled by the roof console box electronics, which will vary the brightness of the LEDs depending on the ambient light and the engine switch condition.
If the ambient light is low the brightness of the LEDs will be decreased when the engine switch is on (IG).
If the ambient light is high there will be no change to the brightness of the LEDs when the engine switch is turned on (IG).
The colour of the LED indicates the status of the system. If there is a system fault during a call the LED will flash red. If there are no system faults, and then the LED will flash green.LED
Condition
Current Status
Green
Continuous
Self test pass, system OK
(no current DTC logged)
Flashing
(0.5 sec ON / 0.75 sec OFF)
- System OK (no current DTC logged), and
- Call being connected, or
- Call in progress, or
- Emergency call mode
Red
Continuous
- Self - test failure (current DTC logged), or
- System test in progress
Flashing
(0.5 sec ON / 0.75 sec OFF)
- Self test failure (current DTC logged), and
- Call being connected, or
- Call in progress
All LEDs
OFF
- Performing power-up self test,
- Stand-by mode, or
- Sleep mode, or
- Service Contract Discontinued
Orange
(Red & Green)
Continuous
Vehicle is not within GSM network range
Flashing
Unit is in Emergency Call Mode
Red/Green
Alternate Flashing
(0.5 second alternating)
(30 second duration after engine switch on (IG))
Unit in service mode
- System OK (no current DTC logged), and
RADIO MUTE
Whenever the mayday ECU is activated, the radio mute signal is also activated and the ECU grounds the MUTE circuit causing the circuit voltage to be pulled low (less than 2 V).
This low voltage is detected by the radio as a mute request and when received, the audio system will mute. The volume of Toyota Link system call can be adjusted by the buttons on the roof console box, refer to MAYDAY ECU BUTTON PAD - Volume Adjustment.AUDIBLE TONES
Audible tones are also provided to indicate the system status and are broadcast via the Toyota Link speaker to alert the customer to certain operating conditions.Tone
Operating Condition
One Beep
Confirms that the system is working correctly.
Two Beeps
If the Toyota Link system is out of GSM range, 2 beeps will be heard when the engine switch is turned off.
Five Beeps
- Attempting to make call when vehicle is not within GSM network range, or if the five tones occur after the engine switch is turned off, the vehicle is not within GSM network range.
- Warning that Service Mode is active or a system malfunction has been detected and a Diagnostic Trouble Code has been stored in the mayday ECU.
- Attempting to make call when vehicle is not within GSM network range, or if the five tones occur after the engine switch is turned off, the vehicle is not within GSM network range.
BACK-UP BATTERY

The back-up battery is housed in the battery compartment of the mayday ECU.
The back-up battery will provide power to the mayday ECU for at least 30 minutes in the event of the vehicle battery being discharged or disconnected.
The ECU has a back-up battery charging circuit that maintains the back-up battery state of charge. This circuit also includes an over current protection device.
The ECU has a back-up battery timer that monitors the time the back-up battery has been in the vehicle. After the backup battery has been in the vehicle for 5 years, it has reached the end of its useful life (internal deterioration causing low charge acceptance) DTC TL14 will be set and the red status LED will be illuminated.BATTERY VOLTAGE
Battery voltage is applied to the mayday ECU at all times via the +B terminal.
If the battery voltage falls below a preset level for longer than 30 minutes, the ECU will transmit a Low Battery Voltage alert to the Toyota Link Call Centre, refer to ALERTS - Low Battery Voltage Alert . If the battery is removed the mayday ECU will transmit an Unauthorised Entry alert to the Toyota Link Call Centre, refer to ALERTS - Unauthorised Entry Alert.BACK-UP BATTERY CHARGER
The mayday ECU constantly monitors both the vehicle battery and back-up battery voltage. The charging circuit constantly monitors the back-up battery voltage to determine if the back-up battery needs to be charged at a maximum of up to 300mA.MAYDAY ECU ANTENNAS
The mayday ECU requires two antennas: one for GPS and the other for GSM. The antennas are located on the rear parcel tray. Each antenna has one lead and a connector.- NOTICE:
- The area directly above the mayday ECU antennas should be free from obstructions as they may adversely affect the antenna operation and the system may not have full functionality. After-market window tinting may also affect the antenna operation, refer to the Toyota Link Owner's Manual for more information.
GSM Antenna:

The GSM antenna is capable of transmitting and receiving voice and data signals via the GSM network.
The mayday ECU uses the GSM network to transmit and receive voice and data. Signal strength may be affected in locations such as basement car parks or tunnels. However, in most cases, as the vehicle emerges from the obstruction or re-enters the digital phone network area, the signal will be available again and any stored data will be transmitted.
The GSM antenna is connected to the mayday ECU by a plug-in type connector.
GPS Antenna:

The GPS antenna receives signals from the satellites orbiting the earth and transmits these to the mayday ECU to determine the vehicles position.
Signals from at least three GPS satellites must be received to accurately determine the vehicle's two dimensional (2D) position. Signals from at least four GPS satellites must be received to accurately determine the vehicle's three dimensional (3D) position.
If signals from only three satellites are received, the mayday ECU cannot determine the vehicle's altitude. GPS reception may be affected in locations such as underground car parks, tunnels, bridges or buildings. The GPS antenna is connected to the mayday ECU by a plug-in type connector.
The ECU uses a principle called triangulation to determine the location of the vehicle. This principle states that you can determine the location of an object if you know its distance from three known locations.
GPS uses 24 satellites orbiting the earth. The location of each satellite is known at any given time. The satellites constantly broadcast radio signals and the mayday ECU GPS module compares the amount of time it takes for the signals from at least three different satellites to reach the GPS module.
By converting time into distance, it can calculate the module's location on Earth.
The ECU receives GPS data, decodes it, and transmits the vehicle's location via SMS when requested by the Toyota Link Call Centre.