2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

TL20 Speaker Circuit Voltage Too Low

Diagnostic trouble codes · Vehicles built from Oct 2006

DESCRIPTION

The Toyota Link system uses the LH rear side speaker to provide a means for voice communication from the Toyota Link Call Centre. Audible tones are also provided to indicate the system status and are broadcast via the speaker to alert the customer to certain operating conditions.
Whenever the Toyota Link system is activated, the radio mute signal is also activated and the mayday ECU grounds the radio mute circuit, causing the circuit voltage to be pulled low (less than 2 V). This low voltage is detected by the radio as a mute request and when received, the audio system will mute.
Whilst the Toyota Link system is not on a call, the mute request from the cellular telephone connector will be passed through the mayday ECU to the audio system.
When a Toyota Link call is active, the mayday ECU will ignore the phone audio and transmit the mayday ECU audio to the speaker.
Light Status
Audible Beeps
Description
All lights flash momentarily
(when the engine switch is turned on (IG))
1
Confirms the system is working correctly.
Flashing red and green light (for 30 sec.)
5
Toyota Link is in Service mode. The beeps will occur every time the engine switch is turned on (IG) or off. Press the Toyota Link button to request this mode be disabled.
The output voltage of the audio amplifier circuit is measured to detect if the speaker is shorted to ground. This test is performed whenever the engine switch is turned on (IG) and only if the audio system is OFF, and the Toyota Link system audio output is muted.
DTC TL20 is set if the speaker circuit voltage is less than 1.8 V.

INSPECTION PROCEDURE


1. CHECK DTCs
  1. Turn the engine switch on (IG).

  1. Select: Diagnosis / DTC List / Current DTC / Clear Current DTCs.

  1. Select: Back / History DTC / Clear Current DTCs.

  1. Turn the engine switch off for 1 minute, then on (IG) again.

  1. Is DTC TL20 reset?



NO
THE PROBLEM IS INTERMITTENT, CHECK THE MAYDAY ECU, WIRE HARNESS AND CONNECTORS
YES


2. CHECK MAYDAY ECU TO AUDIO WIRE HARNESS FOR SHORT TO GROUND

  1. B169483E01
    Disconnect the mayday ECU unit connector N46.

  1. Connect a digital multimeter between terminal 22 and ground and check for continuity.

    Standard:
    Greater than 1 MΩ

  1. Connect a digital multimeter between terminal 23 and ground and check for continuity.

    Standard:
    Greater than 1 MΩ

  1. Is the continuity as specified?



NO
REPAIR OR REPLACE THE WIRE HARNESS TO THE TOYOTA LINK SPEAKER
YES


3. MEASURE SPEAKER RESISTANCE AT MAYDAY ECU

  1. B169483E01
    Connect a digital multimeter between terminals 22 and 23.

  1. Measure the resistance.

    OK:
    Approximately 4 Ω



OK
Go to step 5
NG


4. MEASURE SPEAKER RESISTANCE

  1. B169484E01
    Disconnect the LH rear side speaker connector O12.

  1. Connect a digital multimeter between speaker terminals 1 and 2.

  1. Measure the resistance.

    OK:
    Approximately 4 Ω



NG
REPLACE THE LH REAR SIDE SPEAKER
OK


5. CHECK MAYDAY ECU WIRE HARNESS

  1. B169478E01
    Disconnect the mayday ECU connectors A and B.

  1. Check for continuity between the mayday ECU unit connector N46 and connectors A and B.

    OK:
    Less than 1 Ω



NG
REPAIR OR REPLACE MAYDAY ECU WIRE HARNESS
OK


6. CHECK MAYDAY ECU CONNECTORS
  1. Are the mayday ECU connectors tight?



NO
REPAIR OR REPLACE THE CONNECTORS
YES

REPLACE MAYDAY ECU


← TL19 Speaker Not Detected (from Oct 2006)TL21 Speaker Circuit Voltage Too High (from Oct 2006) →