Home › BRAKE › BRAKE › FRONT BRAKE

FRONT BRAKE > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT DISC


    C132801E01
  1. Align the matchmarks and install the front disc.

    NOTICE:
    When replacing the disc with a new one, select the installation position where the front disc has the minimum runout.



2. TEMPORARILY TIGHTEN FRONT DISC BRAKE BLEEDER PLUG
  1. Temporarily tighten the front disc brake bleeder plug to the disc brake cylinder assembly.



3. INSTALL FRONT DISC BRAKE BLEEDER PLUG CAP
  1. Install the bleeder plug cap to the front disc brake bleeder plug.



4. INSTALL PISTON SEAL
  1. Apply lithium soap base glycol grease to a new piston seal.

  1. Install the piston seal to the disc brake cylinder assembly.



5. INSTALL FRONT DISC BRAKE PISTON
  1. Apply lithium soap base glycol grease to the front disc brake piston and a new cylinder boot.



    C132810E02
  1. Install the cylinder boot to the front disc brake piston.

  1. Install the front disc brake piston to the disc brake cylinder assembly.

    NOTICE:
    Do not install the front disc brake piston forcibly in the disc brake cylinder assembly.



6. INSTALL CYLINDER BOOT


    C132809E05
  1. Install the cylinder boot to the disc brake cylinder assembly.

    NOTICE:
    Install the cylinder boot securely to the grooves of the cylinder assembly and front disc brake piston.

  1. Using a screwdriver, install a new cylinder boot set ring.

    NOTICE:
    1. Install the cylinder boot set ring securely to the grooves of the cylinder boot.
    2. Do not damage the cylinder boot.

    HINT:
    Tape the screwdriver tip before use.



7. INSTALL FRONT DISC BRAKE BUSHING DUST BOOT


    C132799E05
  1. Apply lithium soap base glycol grease to the seal surface of 2 new front disc brake bushing dust boots.

  1. Install the 2 front disc brake bushing dust boots to the front disc brake cylinder mounting.



8. INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSHING


    C132805E02
  1. Apply lithium soap base glycol grease to a new front disc brake cylinder slide bushing.

  1. Install the front disc brake cylinder slide bushing to the No. 2 front disc brake cylinder slide pin.



9. INSTALL NO. 2 FRONT DISC BRAKE CYLINDER SLIDE PIN
  1. Apply the lithium soap base glycol grease to the sliding part and the seal surface of the No. 2 front disc brake cylinder slide pin.



    C142647E04
  1. Install the No. 2 front disc brake cylinder slide pin to the bottom side of the front disc brake cylinder mounting.



10. INSTALL NO. 1 FRONT DISC BRAKE CYLINDER SLIDE PIN


    C132826E02
  1. Apply the lithium soap base glycol grease to the sliding part and the seal surface of the No. 1 front disc brake cylinder slide pin.



    C142648E03
  1. Install the No. 1 front disc brake cylinder slide pin.



11. INSTALL FRONT DISC BRAKE CYLINDER MOUNTING


    C132796
  1. Install the cylinder mounting with the 2 bolts.

    Torque:
    107 N*m{ 1,090 kgf*cm , 79 ft.*lbf }



12. INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE


13. INSTALL FRONT ANTI-SQUEAL SHIM


    C141886E03
  1. Apply front disc brake grease to the anti-squeal shim.

    NOTICE:
    1. When replacing worn pads, the front anti-squeal shim must be replaced together with the pads.
    2. Install the shim in the correct positions and directions.
    3. Apply disc brake grease to the area that contacts the front anti-squeal shim.
    4. Disc brake grease can come out slightly from the area where the front anti-squeal shim is installed.
    5. Make sure that disc brake grease is not applied onto the lining surface.



    C144509E01
  1. Install 2 anti-squeal shims and the 2 pad wear indicators to the each pad.

    NOTICE:
    1. Install the shims in the correct positions and directions.
    2. Install the pad wear indicator in the correct positions and directions.



14. INSTALL FRONT BRAKE PAD
  1. Install the 2 front brake pads with front anti-squeal shim to the front disc brake cylinder mounting.



15. INSTALL ANTI-SQUEAL SPRING (w/ Anti-squeal Spring)


    C171345
  1. Install the 2 anti-squeal springs to the front disc brake pads.

    NOTICE:
    1. When replacing worn pads, the front anti-squeal springs must be replaced at the same time.
    2. Be sure to install the anti-squeal springs into the front disc brake pad installation holes as far as they will go.