Home › BRAKE › BRAKE › REAR BRAKE

REAR BRAKE > REASSEMBLY

for Preparation Click here



1. INSTALL REAR DISC


    C132813E01
  1. Aligning the matchmarks, install the rear disc.

    HINT:
    When replacing the rear disc with a new one, select the installation position where the rear disc has the minimum runout.



2. ADJUST PARKING BRAKE SHOE CLEARANCE
  1. Temporarily install the hub nuts.

  1. Remove the shoe adjusting hole plug.



    C131914E01
  1. Turn the shoe adjuster and expand the shoe until the disc locks.

  1. Turn and contract the shoe adjuster until the disc can rotate smoothly.

    Standard:
    Return 8 notches.

  1. Check that there is no brake drag against the shoe.

  1. Install the shoe adjusting hole plug.

  1. Remove the hub nuts.



3. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG
  1. Install the parking brake shoe adjusting hole plug.



4. TEMPORARILY TIGHTEN REAR DISC BRAKE BLEEDER PLUG
  1. Temporarily install the rear disc brake bleeder plug to the rear disc brake cylinder sub-assembly.



5. INSTALL REAR DISC BRAKE BLEEDER PLUG CAP
  1. Install the rear disc brake bleeder plug cap to the rear disc brake bleeder plug.



6. INSTALL PISTON SEAL
  1. Apply lithium soap base glycol grease to a new piston seal.

  1. Install the piston seal to the rear disc brake cylinder assembly.



7. INSTALL REAR DISC BRAKE PISTON


    C132827E01
  1. Apply lithium soap base glycol grease to the rear disc brake piston and a new cylinder boot.

  1. Install the cylinder boot to the rear disc brake piston.

  1. Install the rear disc brake piston to the rear disc brake cylinder assembly.

    NOTICE:
    Do not install the rear disc brake piston forcibly in the rear disc brake cylinder.



8. INSTALL CYLINDER BOOT


    C133333E01
  1. Install the cylinder boot to the rear disc brake cylinder assembly.

    NOTICE:
    1. Install the cylinder boot securely onto the grooves of the cylinder and the piston.
    2. Do not damage the cylinder boot.

  1. Using a screwdriver, install the set ring.

    NOTICE:
    1. Be careful not to damage the boot.
    2. Install the set ring securely to the grooves of the cylinder boot.

    HINT:
    Tape the screwdriver tip before use.



9. INSTALL REAR DISC BRAKE BUSHING DUST BOOT
  1. Apply lithium soap base glycol grease to the seal surface of 2 new rear disc brake bushing dust boots.



    C132828E01
  1. Install the 2 rear disc brake bushing dust boots to the rear disc brake cylinder mounting.



10. INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN


    C132826E01
  1. Apply the lithium soap base glycol grease to the sliding part and the seal surface of the No. 1 rear disc brake cylinder slide pins.



    C132821
  1. Install the 2 pins (upper and lower) to the bottom side of the rear brake cylinder mounting.



11. INSTALL REAR DISC BRAKE CYLINDER MOUNTING


    C132822
  1. Install the rear disc brake cylinder mounting with the 2 bolts.

    Torque:
    62 N*m{ 632 kgf*cm , 46 ft.*lbf }



12. INSTALL NO. 1 REAR DISC BRAKE PAD SUPPORT PLATE
  1. Install the No. 1 rear disc brake pad support plate to the rear disc brake cylinder mounting.



13. INSTALL NO. 2 REAR DISC BRAKE PAD SUPPORT PLATE
  1. Install the No. 2 rear disc brake pad support plate to the rear disc brake cylinder mounting.



14. INSTALL REAR ANTI-SQUEAL SHIM


    C141885E03
  1. Apply disc brake grease to the inside of the rear anti-squeal shim.

    NOTICE:
    1. When replacing worn pads, the rear anti-squeal shims must be replaced together with the pads.
    2. Apply disc brake grease to the area that contacts the rear anti-squeal shim.
    3. Disc brake grease can come out slightly from the area where the rear anti-squeal shim is installed.
    4. Make sure that disc brake grease is not applied onto the lining surface.



    C144677E02
  1. Install the 2 rear anti-squeal shims and the 2 pad wear indicators to each pad.

    NOTICE:
    Install the pad wear indicator and rear anti-squeal shims in the correct positions and directions.



15. INSTALL REAR BRAKE PAD
  1. Install the 2 rear brake pads with 2 rear anti-squeal shims to the rear disc brake cylinder mounting.