WINDSHIELD GLASS > INSTALLATION |
| 1. INSTALL NO. 2 WINDSHIELD GLASS STOPPER |
Using a brush or sponge, coat the application area of the No. 2 stoppers with Primer G.
Install 2 new No. 2 stoppers onto the windshield glass, as shown in the illustration.
| Area | Dimension |
| A | 13.2 mm (0.519 in.) |

| 2. INSTALL WINDSHIELD GLASS RETAINER |
Using a brush or sponge, coat the application area of the retainers with Primer G.
Install 2 new retainers onto the windshield glass, as shown in the illustration.

| 3. INSTALL NO. 1 WINDSHIELD GLASS STOPPER |
![]() |
Install 2 new No. 1 stoppers to the vehicle body, as shown in the illustration.
| 4. INSTALL WINDSHIELD MOULDING |
Using a brush or sponge, coat the application area of moulding with Primer G.
Install a new moulding onto the windshield glass, as shown in the illustration.

| 5. INSTALL WINDOW GLASS ADHESIVE DAM |
Using a brush or sponge, coat the application area of adhesive dam with Primer G.
Install a new adhesive dam onto the windshield glass, as shown in the illustration.
| Area | Dimension |
| A | 6.5 mm (0.255 in.) |

| 6. INSTALL WINDSHIELD GLASS ASSEMBLY |
![]() |
Position the windshield glass assembly.
Using a suction cup, place the windshield glass assembly in the correct position.
Check that the whole contact surface of the windshield glass rim is perfectly even.
Align the matchmarks on the windshield glass and vehicle body.
Remove the windshield glass assembly.
![]() |
Using a brush, coat the installation surface on the vehicle body with Primer M.
Using a brush or sponge, coat the application area of adhesive with Primer G.
| Area | Dimension |
| a | 8.7 mm (0.342 in.) |
| b | 7.0 mm (0.275 in.) |
| c | 6.5 mm (0.255 in.) |

Apply adhesive (Adhesive: TOYOTA genuine windshield glass adhesive or equivalent).
Cut off the tip of the cartridge nozzle, as shown in the illustration.
| Temperature | Tack-free Time |
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour and 40 minutes |
| 5°C (41°F) | 8 hours |
Load the sealer gun with cartridge.
Apply adhesive to the windshield glass, as shown in the illustration.
| Area | Dimension |
| a | 8.7 mm (0.342 in.) |
| b | 6.5 mm (0.255 in.) |
| c | 12.0 mm (0.472 in.) |
| d | 8.0 mm (0.315 in.) |

![]() |
Install the windshield glass assembly.
Using a suction cup, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.
Lightly press the front surface of the windshield glass to ensure a close fit.
![]() |
If necessary, use a scraper to correct the level or position of adhesive that has been applied.
Hold the windshield glass using protective tape until applied adhesive becomes hard.
| Temperature | Minimum time prior to driving vehicle |
| 35°C (95°F) | 1 hour and 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
| 7. CHECK FOR LEAKS AND REPAIR |
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
| 8. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof) |
| 9. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof) |
| 10. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY |
![]() |
Assemble the front assist grip sub-assembly as shown in the illustration.
![]() |
Install the front assist grip sub-assembly.
| 11. INSTALL VISOR HOLDER |
Engage the 2 claws.
Push in the visor holder and turn it approximately 45°as shown in the illustration.

| 12. INSTALL VISOR ASSEMBLY LH |
![]() |
Engage the 2 clips and install the visor assembly LH.
![]() |
Engage the 4 claws and install the visor bracket cover.
| 13. INSTALL VISOR ASSEMBLY RH |
| 14. INSTALL ROOF CONSOLE BOX ASSEMBLY |
![]() |
Connect the connectors.
Engage the 2 claws and 2 clips, and then install the roof console box assembly.
| 15. INSTALL FRONT PILLAR GARNISH LH |
![]() |
Remove the protective cover.
![]() |
Install a new clip <A> on the front pillar garnish LH.
Engage the 2 claws and 2 clips, then install the front pillar garnish LH.
| 16. INSTALL FRONT PILLAR GARNISH RH |
![]() |
Remove the protective cover.
![]() |
Install a new clip <A> on the front pillar garnish RH.
Engage the 2 claws and 2 clips, then install the front pillar garnish RH.
| 17. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Install the front door opening trim weatherstrip LH as shown in the illustration.
| 18. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Install the front door opening trim weatherstrip RH as shown in the illustration.
| 19. INSTALL RAIN SENSOR TAPE (If replacing rain sensor tape) |
![]() |
Remove the releasing sheet (yellow side) from new rain sensor tape and attach the tape to the position indicated in the illustration (the sensor part of the rain sensor) while pushing out air bubbles with your fingers.
Remove the releasing sheet (white side) from the rain sensor tape.
| Area | Measurement |
| A | 7.3 mm (0.287 in.) |
| B | 13.5 mm (0.531 in.) |
| 20. INSTALL RAIN SENSOR |
![]() |
Connect the connector.
![]() |
Gradually attach the rain sensor to the glass surface to prevent air bubbles from forming between them.
Push in the stopper.
| 21. INSTALL RAIN SENSOR COVER |
![]() |
Install the rain sensor cover.
| 22. INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror) |
![]() |
Slide the inner rear view mirror assembly in the direction indicated by the arrow shown in the illustration to install it.
![]() |
Engage the 2 claws and install the cover.
| 23. INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror) |
![]() |
Slide the inner rear view mirror assembly in the direction indicated by the arrow shown in the illustration to install it.
![]() |
Using a "TORX" socket wrench (T20), install the inner rear view mirror with the screw.
Connect the connector.
| 24. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror) |
![]() |
Engage the 6 claws and temporarily install the inner rear view mirror stay holder cover.
![]() |
Slide the inner rear view mirror stay holder cover and engage the 2 claws as shown in the illustration to install the cover.
| 25. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
![]() |
Engage the 4 claws and install the cowl top ventilator louver sub-assembly.
Install the 2 clips.
| 26. INSTALL FRONT FENDER TO COWL SIDE SEAL RH |
![]() |
Engage the claw and install the front fender to cowl side seal RH.
| 27. INSTALL FRONT FENDER TO COWL SIDE SEAL LH |
![]() |
Engage the claw and install the front fender to cowl side seal LH.
| 28. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 29. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
![]() |
Clean the wiper arm serrations.
When reinstalling:
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.
| Area | Measurement |
| A | 37 to 52 mm (1.46 to 2.05 in.) |
| 30. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
Operate the wiper and stop the windshield wiper motor at the automatic stop position.
![]() |
Clean the wiper arm serrations.
When reinstalling:
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.
| Area | Measurement |
| A | 23 to 38 mm (0.90 to 1.49 in.) |
Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.
| 31. INSPECT SRS WARNING LIGHT |