WINDSHIELD GLASS > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Remove the nut and the front wiper arm and blade assembly LH.
| 4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH |
![]() |
Remove the nut and the front wiper arm and blade assembly RH.
| 5. REMOVE FRONT FENDER TO COWL SIDE SEAL LH |
![]() |
Disengage the claw and remove the front fender to cowl side seal LH.
| 6. REMOVE FRONT FENDER TO COWL SIDE SEAL RH |
![]() |
Disengage the claw and remove the front fender to cowl side seal RH.
| 7. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
![]() |
Remove the 2 clips.
Disengage the 4 claws and remove the cowl top ventilator louver sub-assembly.
| 8. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror) |
![]() |
Disengage the 2 claws and the cover.
![]() |
Pull the lever in the direction indicated by the arrow shown in the illustration and slide the inner rear view mirror assembly upward to remove it.
| 9. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror) |
![]() |
Disengage the 2 claws and slide the inner rear view mirror stay holder cover as shown in the illustration.
![]() |
Disengage the 6 claws and remove the inner rear view mirror stay holder cover.
| 10. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror) |
![]() |
Disconnect the connector.
Using a "TORX" socket wrench (T20), remove the screw and the inner rear view mirror.
![]() |
Slide the inner rear view mirror assembly in the direction indicated by the arrow shown in the illustration to remove it.
| 11. REMOVE RAIN SENSOR COVER |
![]() |
Remove the rain sensor cover.
| 12. REMOVE RAIN SENSOR |
![]() |
Release the stopper by pulling the stopper down and disconnect the rain sensor as shown in the illustration.
![]() |
Disconnect the connector and remove the rain sensor.
| 13. REMOVE RAIN SENSOR TAPE (If replacing rain sensor tape) |
Remove the rain sensor tape.
| 14. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 15. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
| 16. REMOVE FRONT PILLAR GARNISH LH |
![]() |
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 2 claws and remove the front pillar garnish LH.
Remove the clip <A> from the vehicle body.
![]() |
Protect the curtain shield airbag assembly.
Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.
| 17. REMOVE FRONT PILLAR GARNISH RH |
![]() |
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 2 claws and remove the front pillar garnish RH.
Remove the clip <A> from the vehicle body.
![]() |
Protect the curtain shield airbag assembly.
Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.
| 18. REMOVE ROOF CONSOLE BOX ASSEMBLY |
![]() |
Using a moulding remover, disengage the 2 clips and 2 claws.
Disconnect the connectors and remove the roof console box assembly.
| 19. REMOVE VISOR ASSEMBLY LH |
![]() |
Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.
![]() |
Disengage the 2 clips and remove the visor assembly LH.
| 20. REMOVE VISOR ASSEMBLY RH |
| 21. REMOVE VISOR HOLDER |
Turn the visor holder approximately 45°and pull it out as shown in the illustration.
Disengage the 2 claws and remove the visor holder.

| 22. REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY |
![]() |
Using a screwdriver, disengage the 6 claws and remove the 2 assist grip covers.
![]() |
Disengage the 2 clips and remove the front assist grip sub-assembly.
| 23. REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof) |
| 24. REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof) |
| 25. REMOVE WINDSHIELD MOULDING |
![]() |
Using a knife, cut off the moulding, as shown in the illustration.
Remove the remaining moulding from the windshield glass.
| 26. REMOVE WINDSHIELD GLASS ASSEMBLY |

![]() |
Apply protective tape to the installation position of the windshield glass assembly on the vehicle body.
![]() |
Pass a piano wire between the vehicle body and glass from the interior.
Tie both wire ends to wooden blocks or similar objects.
Cut off the adhesive by pulling the piano wire around the windshield glass.
![]() |
Place matchmarks on the windshield glass and vehicle body on the locations indicated in the illustration.
Using a suction cup, remove the windshield glass assembly.
| 27. REMOVE WINDOW GLASS ADHESIVE DAM |
Using a scraper, remove the adhesive dam.
| 28. REMOVE NO. 2 WINDSHIELD GLASS STOPPER |
Using a scraper, remove the 2 No. 2 stoppers.
| 29. REMOVE WINDSHIELD GLASS RETAINER |
Using a scraper, remove the 2 retainers.
| 30. REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-Piece Type) |
![]() |
Remove the 2 No. 1 stoppers.
| 31. CLEAN WINDSHIELD GLASS |
![]() |
Using a scraper, remove the adhesive tape and adhesive sticking to the windshield glass.
Clean the outer circumference of the windshield glass with a non-residue solvent.
| 32. CLEAN VEHICLE BODY |
![]() |
Clean and shape the contact surface of the vehicle body.
Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.
Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.