REAR DOOR BLACK OUT TAPE > INSTALLATION |
| 1. REPAIR INSTRUCTION |
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
Wipe off any tape adhesive residue with cleaner.
Installation temperature
When ambient temperature is below 15°C, perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 and 30°C using a heat light. When ambient temperature is above 35°C, cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 and 30°C prior to installation.
Before installation
Remove any roughness of coating and dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame). If any roughness or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.
Key points for handling the tape
The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.
Key points for installation of the tape (how to use a squeegee and installation procedure for flat surfaces)
To avoid air bubbles, slightly raise the part of the tape that are going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee at a 40 to 50° (for pressing forward) or 30 to 45° (for pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf) at a constant slow speed of 3 to 7 cm per second.

Key points for installation of the tape (how to use a squeegee and installation procedure for hemming surfaces)
![]() |
If it is difficult to press the tape, press it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.
Key points for installation of the tape (how to use a squeegee and installation procedure for corners)
Remove the release paper and apply the tape carefully with your fingers.
Before applying the tape to each corner, heat the tape using a heat light and gradually apply it, to avoid wrinkles on the tape and achieve a neat finish.
Check after installation
After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, reapply using new tape.
| 2. INSTALL REAR DOOR LOWER OUTSIDE STRIPE |
Refer to the illustration to position the rear door lower outside stripe.

Remove the release paper and apply the stripe.
| 3. INSTALL REAR DOOR OUTSIDE STRIPE |
Refer to the illustration to position the rear door outside stripe.

Remove the release paper and apply the stripe.
| 4. INSTALL REAR DOOR FRAME GARNISH |
![]() |
Engage the clip and install a new rear door frame garnish.
| 5. INSTALL REAR DOOR WEATHERSTRIP |
![]() |
Engage the clip and install the rear door weatherstrip.
| 6. INSTALL REAR DOOR GLASS SUB-ASSEMBLY |
![]() |
Slide the rear door glass sub-assembly to install it as shown in the illustration.
| 7. INSTALL REAR DOOR QUARTER WINDOW GLASS |
Install the rear door quarter window glass to the rear door quarter window weatherstrip.
![]() |
Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.
| 8. INSTALL REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY |
Insert the rear door lower window frame sub-assembly from above.
Install the rear door glass run to the rear door lower window frame sub-assembly.
![]() |
Install the rear door lower window frame sub-assembly with the 2 bolts and screw.
| 9. INSTALL REAR DOOR GLASS RUN |
![]() |
Install the rear door glass run.
| 10. INSTALL REAR DOOR SERVICE HOLE COVER |
Apply butyl tape to the rear door panel.
![]() |
Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.
Install the new rear door service hole cover.
Connect the connector and clamp.
| 11. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY |
![]() |
Connect the rear door lock remote control cable and rear door inside locking cable to the rear inside handle.
![]() |
Engage the 2 claws and install the rear door inside handle sub-assembly.
| 12. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP |
![]() |
Engage the 3 claws to install the rear door inner glass weatherstrip.
| 13. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Engage the claw to install the No. 1 door scuff plate clamp.
Connect each connector.
![]() |
Engage the rear door trim board with the 4 clips of the rear door inner glass weatherstrip.
![]() |
Engage the 7 clips to install the rear door trim board to the rear door panel.
Install the 3 screws.
| 14. INSTALL DOOR ASSIST GRIP COVER |
![]() |
Engage the 6 claws and install the door assist grip cover.
| 15. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Engage the 3 claws to install the rear door inside handle bezel plug.