SFI SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the tester, read the "Data List".
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed | Vehicle speed: Min.: 0 km/h, Max.: 255 km/h | Actual vehicle speed | Speed indicated on speedometer |
| Engine Speed | Engine speed: Min.: 0 rpm, Max.: 16383 rpm |
| - |
| Calculate Load | Calculated load by ECM: Min.: 0%, Max.: 100% |
| - |
| Vehicle Load | Vehicle load: Min.: 0%, Max.: 25700% | Actual vehicle load | Load percentage in terms of maximum intake air flow amount |
| MAF | Air flow rate from mass air flow meter sub-assembly: Min.: 0 gm/sec, Max.: 655.35 gm/sec | 1 to 3 g/sec.: Idling 6 to 10 g/sec.: Running without load at 2500 rpm | If value approximately 0.0 gm/sec:
|
| Atmosphere Pressure | Atmospheric pressure: Min.: 0 kPa, Max.: 255 kPa | Equivalent to atmospheric pressure (absolute pressure) | - |
| Coolant Temp | Engine coolant temperature: Min.: -40°C (-40°F), Max.: 140°C (284°F) | 80 to 105°C (176 to 221°F): After warming up |
|
| Intake Air | Intake air temperature: Min.: -40°C (-40°F), Max.: 140°C (284°F) | Equivalent to ambient air temperature |
|
| Engine Run Time | Engine run time: Min.: 0 s, Max.: 65535 s | Time since engine start | - |
| Initial Engine Coolant Temp | Engine coolant temperature at engine start: Min.: -40°C (-40°F), Max.: 120°C (248°F) | - | - |
| Initial Intake Air Temp | Intake air temperature at engine start: Min.: -40°C (-40°F), Max.: 120°C (248°F) | - | - |
| Battery Voltage | Battery voltage: Min.: 0 V, Max.: 65.5 V | 11 to 14 V: ignition switch ON | - |
| Accel Sens. No. 1 Volt % | Absolute accelerator pedal position No. 1: Min.: 0%, Max.: 100% | 10 to 22%: Accelerator pedal released 52 to 90%: Accelerator pedal fully depressed | - |
| Accel Sens. No. 2 Volt % | Absolute accelerator pedal position No. 2: Min.: 0%, Max.: 100% | 24 to 40%: Accelerator pedal released 68 to 100%: Accelerator pedal fully depressed | - |
| Accel Sensor Out No. 1 | Accelerator pedal position sensor No. 1 voltage: Min.: 0 V, Max.: 4.9 V | - | - |
| Accel Sensor Out No. 2 | Accelerator pedal position sensor No. 2 voltage: Min.: 0 V, Max.: 4.9 V | - | - |
| Accel Sensor Out No. 1 | Accelerator pedal position sensor No. 1 voltage: Min.: 0 V, Max.: 4.9 V | 0.5 to 1.1 V: Accelerator pedal released 2.5 to 4.5 V: Accelerator pedal fully depressed | - |
| Accel Sensor Out No. 2 | Accelerator pedal position sensor No. 2 voltage: Min.: 0 V, Max.: 4.9 V | 1.2 to 2.0 V: Accelerator pedal released 3.4 to 5.0 V: Accelerator pedal fully depressed | - |
| Accelerator Idle Position | Whether or not accelerator pedal position sensor detecting idle: ON or OFF | ON: Idling | - |
| Accel Fully Close #1 (AD) | Accelerator fully closed value No. 1 voltage (AD): Min.: 0 V, Max.: 4.9 V | - | Electronic throttle control system service data |
| Accel Fully Close Learn #1 | Accelerator fully closed learning value No. 1: Min.: 0 deg, Max.: 124.5 deg | - | Electronic throttle control system service data |
| Accel Fully Close Learn #2 | Accelerator fully closed learning value No. 2: Min.: 0 deg, Max.: 124.5 deg | - | Electronic throttle control system service data |
| Throttle Sensor Volt % | Throttle valve opening percentage according to throttle position sensor: Min.: 0%, Max.: 100% |
| Value calculated based on the voltage at terminal VTA1 |
| Throttl Sensor #2 Volt % | Throttle valve opening percentage according to throttle position sensor No. 2: Min.: 0%, Max.: 100% |
| Value calculated based on the voltage at terminal VTA2 |
| ST1 | Brake pedal signal: ON or OFF | OFF: Brake pedal released | - |
| System Guard | System guard: ON or OFF | - | Electronic throttle control system service data |
| Throttle Idle Position | Whether or not throttle position sensor detecting idle: ON or OFF |
| - |
| Throttle Require Position | Required throttle position: Min.: 0 V, Max.: 4.9 V | 0.5 to 1.1 V: Idling | - |
| Throttle Sensor Position*1 | Throttle position sensor: Min.: 0%, Max.: 100% |
| Recognition value for throttle opening angle on ECM |
| Throttle Position No. 1 | Throttle position sensor No. 1 output voltage: Min.: 0 V, Max.: 4.98 V | - | - |
| Throttle Position No. 2 | Throttle position sensor No. 2 output voltage: Min.: 0 V, Max.: 4.98 V | - | - |
| Throttle Position No. 1 | Throttle position sensor No. 1 output voltage: Min.: 0 V, Max.: 4.98 V |
| - |
| Throttle Position No. 2 | Throttle position sensor No. 2 output voltage: Min.: 0 V, Max.: 4.98 V |
| - |
| Throttle Position Command | Throttle position command value: Min.: 0 V, Max.: 4.9 V | 0.5 to 4.8 V | - |
| Throttle Sens Open Pos #1 | Throttle sensor opener position No. 1: Min.: 0 V, Max.: 4.9 V | 0.6 to 1.4 V | Electronic throttle control system service data |
| Throttle Sens Open Pos #2 | Throttle sensor opener position No. 2: Min.: 0 V, Max.: 4.9 V | 1.7 to 2.5 V | Electronic throttle control system service data |
| Throttle Sens Open #1 (AD) | Throttle position sensor No. 1 output voltage (AD): Min.: 0 V, Max.: 4.9 V | 0.5 to 4.8 V | - |
| Throttle Motor | Whether or not throttle actuator control permitted: ON or OFF | ON: ignition switch ON OFF: Electronic throttle control system has failed | - |
| Throttle Motor Current | Throttle actuator current: Min.: 0 A, Max.: 19.9 A | 0 to 3.0 A: Idling | Electronic throttle control system service data |
| Throttle Motor DUTY | Throttle actuator: Min.: 0%, Max.: 100% | 10 to 22%: Idling after engine warmed up | Electronic throttle control system service data |
| Throttle Motor Duty (Open) | Throttle actuator duty ratio (open): Min.: 0%, Max.: 100% | 0 to 40%: Idling | Electronic throttle control system service data |
| Throttle Motor Duty (Close) | Throttle actuator duty ratio (close): Min.: 0%, Max.: 100% | 0 to 40%: Idling | Electronic throttle control system service data |
| ETCS Actuator Power | Electronic throttle control system power supply: ON or OFF | ON: ignition switch ON and system normal OFF: Electronic throttle control system has failed | - |
| +BM Voltage | +BM voltage: Min.: 0 V, Max.: 19.9 V | 11 to 14 V: ignition switch ON and system normal | Electronic throttle control system service data |
| Actuator Power Supply | Throttle actuator power supply: ON or OFF |
| - |
| Fail Safe Drive | Whether or not fail safe function executed: ON or OFF | ON: Electronic throttle control system has failed OFF: Electronic throttle control system normal | Electronic throttle control system service data |
| Fail Safe Drive (Main CPU) | Whether or not fail safe function executed: ON or OFF | ON: Electronic throttle control system has failed OFF: Electronic throttle control system normal | Electronic throttle control system service data |
| Injector (Port) | Injection duration of No. 1 cylinder: Min.: 0 ms, Max.: 32.64 ms | 1.92 to 3.37 ms: Idling with warm engine | - |
| Injection Volum (Cylinder 1) | Injection volume (cylinder 1): Min.: 0 ml, Max.: 2.047 ml | 0.05 to 0.15 ml: idling with warm engine | Total fuel injection volume of 10 injections |
| Fuel Pump/Speed Status | Fuel pump/status: ON or OFF | ON: Cranking | - |
| EVAP (Purge) VSV | Purge VSV control duty: Min.: 0%, Max.: 100% | 10 to 50%: Idling with warm engine | Order signal from ECM |
| EVAP Purge Flow | Purge flow: Min.: 0%, Max.: 102.3% | 0 to 10%: Idling with warm engine | - |
| Purge Density Learn Value | Learning value of purge density: Min.: -50, Max.: 349.99 | -40 to 10: Idling with warm engine | - |
| EVAP Purge VSV | Purge VSV status: ON or OFF | OFF: Engine moving at 3000 rpm or more after warming up ON: Accelerator pedal released | - |
| Target Air-Fuel Ratio | Ratio compared to stoichiometric level: Min.: 0, Max.: 1.998 | 0.8 to 1.2: Idling with warm engine |
|
| AF Lambda B1S1 | Short-term fuel trim associated with bank 1 sensor 1: Min.: 0, Max.: 1.99 |
| - |
| AFS Voltage B1S1 | Air fuel ratio sensor output voltage for bank 1 sensor 1: Min.: 0 V, Max.: 7.99 V | 2.8 to 3.8 V: Idling | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of air fuel ratio sensor |
| AFS Current B1S1 | Air fuel ratio sensor current for bank 1 sensor 1: Min.: -128 mA, Max.: 127.99 mA | - | - |
| O2S B1S2 | Heated oxygen sensor output voltage for bank 1 sensor 2: Min.: 0 V, Max.: 1.27 V | 0.1 to 0.9 V: Driving at 70 km/h (44 mph) | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of heated oxygen sensor |
| Short FT #1 | Short-term fuel trim of bank 1: Min.: -100%, Max.: 99.2% | -20 to 20% | Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio |
| Long FT #1 | Long-term fuel trim of bank 1: Min.: -100%, Max.: 99.2% | -15 to 15% | Overall fuel compensation carried out long-term to compensate continual deviation of short-term fuel trim from central value |
| Total FT #1 | Total fuel trim value for fuel system: Min.: -0.5, Max.: 0.496 | -0.2 to 0.2: Idling | - |
| Fuel System Status #1 | Fuel system status (bank 1): OL or CL or OLDrive or OLFault or CLFault | CL: Idling after warming up |
|
| Fuel System Status #2 | - | Unused | - |
| IGN Advance | Ignition timing advance for No. 1 cylinder: Min.: -64 deg, Max.: 63.5 deg | BTDC 5 to 15 deg.: Idling | - |
| Knock Feedback Value | Feedback value of knocking: Min.: -64 °CA, Max.: 1984 °CA | -20 to 0 °CA: Driving at 70 km/h (44 mph) | - |
| Knock Correct Learn Value | Correction learning value of knocking: Min.: -64 °CA, Max.: 1984 °CA | 0 to 20 °CA: Driving at 70 km/h (44 mph) | - |
| VVT Control Status #1 | VVT control (bank 1) status: ON or OFF | - | - |
| VVT Aim Angle #1*2 | VVT aim angle (bank 1): Min.: 0%, Max.: 100% | 0 to 100% | VVT duty signal value during intrusive operation |
| VVT Change Angle #1*2 | VVT change angle (bank 1): Min.: 0 DegFR, Max.: 60 DegFR | 0 DegFR: Idling | Displacement angle during intrusive operation |
| VVT OCV Duty #1*2 | VVT camshaft timing oil control valve assembly operation duty: Min.: 0%, Max.: 100% | 0 to 100% | Requested duty value for intrusive operation |
| Starter Signal | Starter signal: ON or OFF | ON: Starter signal on OFF: Starter signal off | - |
| Power Steering Signal | Power steering signal: ON or OFF | ON: Power steering operation | - |
| Power Steer Sig. Record | Power steering signal: ON or OFF | ON: When steering wheel first turned after ignition switch turned ON | - |
| Neutral Position SW Signal | Park/neutral position switch assembly status: ON or OFF | ON: P or N position | - |
| Stop Light Switch | Stop light switch assembly: ON or OFF | ON: Brake pedal depressed | - |
| A/C Signal | A/C signal: ON or OFF | ON: Air conditioning on | - |
| Closed Throttle Position SW | Closed throttle position switch: ON or OFF |
| - |
| Electrical Load Signal | Electrical load signal: ON or OFF | ON: Headlights or defogger turned on | - |
| Check Mode | Check mode: ON or OFF | ON: Check mode on | Click here
|
| SPD Test Result | Check mode result for vehicle speed sensor: Compl or Incmpl | - | - |
| Misfire Test Result | Check mode result for misfire monitor: Compl or Incmpl | - | - |
| OXS1 Test Result | Check mode result for heated oxygen sensor (bank 1): Compl or Incmpl | - | - |
| A/F Test Results #1 | Check mode result for air fuel ratio sensor (bank 1): Compl or Incmpl | - | - |
| Complete Parts Monitor | Comprehensive component monitor: Not Avl or Avail | - | - |
| Fuel System Monitor | Fuel system monitor: Not Avl or Avail | - | - |
| Misfire Monitor | Misfire monitor: Not Avl or Avail | - | - |
| O2S (A/FS) Heater Monitor | O2S (A/FS) heater monitor: Not Avl or Avail | - | - |
| Catalyst Monitor | Catalyst monitor: Not Avl or Avail | - | - |
| # Codes (Include History) | #Codes: Min.: 0, Max.: 255 | - | Number of detected DTCs |
| MIL | MIL status: ON or OFF | ON: MIL on | - |
| Time after DTC Cleared | Time after DTC cleared: Min.: 0 min, Max.: 65535 min | Equivalent to time after DTCs cleared | - |
| Distance from DTC Cleared | Distance after DTC cleared: Min.: 0 km, Max.: 65535 km | Equivalent to drive distance after DTCs cleared | - |
| Warmup Cycle Cleared DTC | Warm-up cycle after DTC cleared: Min.: 0, Max.: 255 | - | Number of warm-up cycles after DTC cleared |
| OBD Requirements | OBD Requirements | E-OBD | - |
| Number of Emission DTC | Emission related DTCs: Min.: 0, Max.: 127 | - | Number of emission related DTCs |
| TC and TE1 | TC and TE1 terminals of DLC3: ON or OFF | - | - |
| Ignition Trig. Count | Ignition counter: Min.: 0, Max.: 65535 | 0 to 400 | - |
| Cylinder #1 Misfire Count | Misfire count of cylinder 1: Min.: 0, Max.: 255 | 0 | - |
| Cylinder #2 Misfire Count | Misfire count of cylinder 2: Min.: 0, Max.: 255 | 0 | - |
| Cylinder #3 Misfire Count | Misfire count of cylinder 3: Min.: 0, Max.: 255 | 0 | - |
| Cylinder #4 Misfire Count | Misfire count of cylinder 4: Min.: 0, Max.: 255 | 0 | - |
| All Cylinders Misfire Count | Misfire count of all cylinders: Min.: 0, Max.: 255 | 0 to 35 | - |
| Misfire RPM | Engine speed when misfire occurs: Min.: 0 rpm, Max.: 6375 rpm | - | - |
| Misfire Load | Engine load when misfire occurred: Min.: 0 g/rev, Max.: 3.98 g/rev | - | - |
| Electric Fan Motor | Electric fan motor: ON or OFF | - | - |
| Idle Fuel Cut | Fuel cut idle: ON or OFF | ON: Fuel cut operating | Idle Fuel Cut = "ON" when throttle valve fully closed and engine speed over 2500 rpm |
| FC TAU | Fuel cut TAU (Fuel cut during very light load): ON or OFF | ON: Fuel cut operating | Fuel cut being performed under very light load to prevent incomplete engine combustion |
| Model Code | Identifies model code | ACV40 | - |
| Engine Type | Identifies engine type | 2AZFE | - |
| Cylinder Number | Identifies number of cylinders | 4 | - |
| Transmission Type | Identifies transmission type | M/T or ECT 5th | - |
| Destination | Identifies destination | W | - |
| Model Year | Identifies model year | 201# | - |
| System Identification | Identifies engine system | Gasoline | - |
| Engine Speed of Cyl #1 | Engine speed during No. 1 cylinder fuel cut: Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression performed using Active Test 51199 rpm: Active Test not performed |
| Engine Speed of Cyl #2 | Engine speed during No. 2 cylinder fuel cut: Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression performed using Active Test 51199 rpm: Active Test not performed |
| Engine Speed of Cyl #3 | Engine speed during No. 3 cylinder fuel cut: Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression performed using Active Test 51199 rpm: Active Test not performed |
| Engine Speed of Cyl #4 | Engine speed during No. 4 cylinder fuel cut: Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression performed using Active Test 51199 rpm: Active Test not performed |
| Av Engine Speed of All Cyl | Engine speed for all cylinders during fuel cut: Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression performed using Active Test 51199 rpm: Active Test not performed |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed | Vehicle speed: Min.: 0 km/h, Max.: 255 km/h | Actual vehicle speed | Speed indicated on speedometer |
| Engine Speed | Engine speed: Min.: 0 rpm, Max.: 16383 rpm | 650 to 750 rpm: Idling: (M/T) 620 to 720 rpm: Idling: (A/T) | - |
| Calculate Load | Calculated load by ECM: Min.: 0%, Max.: 100% |
| - |
| Vehicle Load | Vehicle load: Min.: 0%, Max.: 25700% | Actual vehicle load | Load percentage in terms of maximum intake air flow amount |
| MAF | Air flow rate from mass air flow meter sub-assembly: Min.: 0 gm/sec., Max.: 655.35 gm/sec. | 1 to 3 g/sec.: Idling 6 to 10 g/sec.: Running without load at 2500 rpm | If value is approximately 0 gm/sec.:
|
| Atmosphere Pressure | Atmospheric pressure: Min.: 0 kPa, Max.: 255 kPa | Equivalent to the atmosphere pressure (absolute pressure) | - |
| Coolant Temp | Engine coolant temperature: Min.: -40°C, Max.: 140°C | 80 to 105°C (176 to 221°F): After warming up |
|
| Intake Air | Intake air temperature: Min.: -40°C, Max.: 140°C | Equivalent to ambient air temperature |
|
| Engine Run Time | Engine run time: Min.: 0 s, Max.: 65535 s | Time since engine started | - |
| Initial Engine Coolant Temp | Engine coolant temperature at engine start: Min.: -40°C, Max.: 119.3°C | - | - |
| Initial Intake Air Temp | Intake air temperature at engine start: Min.: -40°C, Max.: 119.3°C | - | - |
| Battery Voltage | Battery voltage: Min.: 0 V, Max.: 65.535 V | 11 to 14 V: Ignition switch ON | - |
| Accelerator Position | Accelerator pedal position: Min.: 0%, Max.: 399.9% | Actual accelerator pedal position | - |
| Accel Sens. No. 1 Volt % | Absolute accelerator pedal position No. 1: Min.: 0%, Max.: 100% | 10 to 22%: Accelerator pedal released 52 to 90%: Accelerator pedal fully depressed | - |
| Accel Sens. No. 2 Volt % | Absolute accelerator pedal position No. 2: Min.: 0%, Max.: 100% | 24 to 40%: Accelerator pedal released 68 to 100%: Accelerator pedal fully depressed | - |
| Accel Sensor Out No. 1 | Accelerator pedal position sensor No. 1 voltage: Min.: 0 V, Max.: 4.98 V | - | - |
| Accel Sensor Out No. 2 | Accelerator pedal position sensor No. 2 voltage: Min.: 0 V, Max.: 4.98 V | - | - |
| Accel Sensor Out No. 1 | Accelerator pedal position sensor No. 1 voltage: Min.: 0 V, Max.: 4.98 V | 0.5 to 1.1 V: Accelerator pedal released 2.6 to 4.5 V: Accelerator pedal fully depressed | - |
| Accel Sensor Out No. 2 | Accelerator pedal position sensor No. 2 voltage: Min.: 0 V, Max.: 4.98 V | 1.2 to 2.0 V: Accelerator pedal released 3.4 to 4.98 V: Accelerator pedal fully depressed | - |
| Accelerator Idle Position | Whether or not accelerator pedal position sensor detecting idle: ON or OFF | ON: Idling | - |
| Accel Fully Close Learn #1 | Accelerator fully closed learning value No. 1: Min.: 0 deg., Max.: 124.5 deg. | - | Electronic throttle control system service data |
| Accel Fully Close Learn #2 | Accelerator fully closed learning value No. 2: Min.: 0 deg., Max.: 124.5 deg. | - | Electronic throttle control system service data |
| Throttle Sensor Volt % | Throttle valve opening percentage according to throttle position sensor: Min.: 0%, Max.: 100% |
| Value calculated based on the voltage at terminal VTA1 |
| Throttl Sensor #2 Volt % | Throttle valve opening percentage according to throttle position sensor No. 2: Min.: 0%, Max.: 100% |
| Value calculated based on the voltage at terminal VTA2 |
| ST1 | Brake pedal signal: ON or OFF | OFF: Brake pedal released | - |
| System Guard | System guard: ON or OFF | - | Electronic throttle control system service data |
| Open Side Malfunction | Open side malfunction: ON or OFF | - | Electronic throttle control system service data |
| Throttle Idle Position | Whether or not throttle position sensor detecting idle: ON or OFF | ON: Accelerator pedal released OFF: Accelerator pedal fully depressed | - |
| Throttle Require Position | Required throttle position: Min.: 0 V, Max.: 4.98 V | 0.5 to 1.1 V: Idling | - |
| Throttle Sensor Position*1 | Throttle position sensor: Min.: 0%, Max.: 100% |
| Recognition value for throttle opening angle on ECM |
| Throttle Position No. 1 | Throttle position sensor No. 1 output voltage: Min.: 0 V, Max.: 4.98 V | - | - |
| Throttle Position No. 2 | Throttle position sensor No. 2 output voltage: Min.: 0 V, Max.: 4.98 V | - | - |
| Throttle Position No. 1 | Throttle position sensor No. 1 output voltage: Min.: 0 V, Max.: 4.98 V |
| - |
| Throttle Position No. 2 | Throttle position sensor No. 2 output voltage: Min.: 0 V, Max.: 4.98 V |
| - |
| Throttle Position Command | Throttle position command value: Min.: 0 V, Max.: 4.98 V | 0.5 to 4.8 V | - |
| Throttle Sens Open Pos #1 | Throttle sensor opener position No. 1: Min.: 0 V, Max.: 4.98 V | 0.6 to 1.4 V | Electronic throttle control system service data |
| Throttle Sens Open Pos #2 | Throttle sensor opener position No. 2: Min.: 0 V, Max.: 4.98 V | 1.7 to 2.5 V | Electronic throttle control system service data |
| Throttle Motor Current | Throttle actuator current: Min.: 0 A, Max.: 19.9 A | 0 to 3.0 A: Idling | Electronic throttle control system service data |
| Throttle Motor DUTY | Throttle actuator: Min.: 0%, Max.: 100% | 10 to 20%: Idling after engine warmed up | Electronic throttle control system service data |
| Throttle Motor Current | Throttle actuator current: Min.: 0 A, Max.: 19.92 A | 0 to 3.0 A: Idling | - |
| Throttle Motor Open Duty | Throttle actuator open duty ratio: Min.: 0%, Max.: 255% | 0 to 40%: Idling | - |
| Throttle Motor Close Duty | Throttle actuator close duty ratio: Min.: 0%, Max.: 255% | 0 to 40%: Idling | - |
| Throttle Motor Duty (Open) | Throttle actuator duty ratio (open): Min.: 0%, Max.: 255% | 0 to 40%: Idling | Electronic throttle control system service data |
| Throttle Motor Duty (Close) | Throttle actuator duty ratio (closed): Min.: 0%, Max.: 255% | 0 to 40%: Idling | Electronic throttle control system service data |
| Throttle Fully Close Learn | Throttle valve fully closed (learned value): Min.: 0 V, Max.: 4.98 V | 0.4 to 1.0 V: Accelerator pedal released | - |
| +BM Voltage | +BM voltage: Min.: 0 V, Max.: 79.998 V | 11 to 14 V: Ignition switch ON and system normal | Electronic throttle control system service data |
| Actuator Power Supply | Throttle actuator power supply: ON or OFF |
| - |
| Throttle Position | Throttle valve opening angle: Min.: 0 deg, Max.: 499.99 deg | - | When the engine stalls, is difficult to start, or idles roughly |
| ISC Flow | Flow rate calculated from information from each sensor: Min.: 0 L/s, Max.: 79.99 L/s | - | When the engine stalls, is difficult to start, or idles roughly |
| ISC Position | Target valve opening angle calculated from ISC: Min.: 0 deg, Max.: 499.99 deg | - | When the engine stalls, is difficult to start, or idles roughly |
| ISC Feedback Value | ISC feedback value: Min.: -40 L/s, Max.: 39.99 L/s | - | When the engine stalls, is difficult to start, or idles roughly |
| ISC Learning Value | ISC learning value: Min.: -40 L/s, Max.: 39.99 L/s | - | When the engine stalls, is difficult to start, or idles roughly |
| Electric Load Feedback Val | Electrical load feedback value: Min.: -40 L/s, Max.: 39.99 L/s | - | When the engine stalls, is difficult to start, or idles roughly |
| Air Conditioner FB Val | Air conditioner load feedback value: Min.: -40 L/s, Max.: 39.99 L/s | - | When the engine stalls, is difficult to start, or idles roughly |
| Low Revolution Control | Status of low engine speed control: ON or OFF | - | When the engine stalls, is difficult to start, or idles roughly |
| N Range Status | Judgment for shift lever N position: ON or OFF | - | When the engine stalls, is difficult to start, or idles roughly |
| Eng Stall Control FB Flow | Feedback value of intake air flow: Min.: -40 L/s, Max.: 39.99 L/s | - | When the engine stalls, is difficult to start, or idles roughly |
| Injector (Port) | Injection duration of No. 1 cylinder: Min.: 0 μs., Max.: 65535 μs. | 1920 to 3370 μs.: Idling with warm engine | - |
| Injection Volum (Cylinder 1) | Injection volume (cylinder 1): Min.: 0 ml, Max.: 2.047 ml | 0.05 to 0.15 ml: Idling with warm engine | Total fuel injection volume of 10 injections |
| Fuel Pump/Speed Status | Fuel pump status: ON or OFF | ON: Cranking | - |
| EVAP (Purge) VSV | Purge VSV control duty: Min.: 0%, Max.: 100% | 10 to 50%: Idling with warm engine | Order signal from ECM |
| EVAP Purge Flow | Ratio of evaporative purge flow to intake air volume: Min.: 0%, Max.: 399.9% | 0 to 10%: Idling with warm engine | - |
| Purge Density Learn Value | Learning value of purge density: Min.: -200, Max.: 199.993 | -40 to 10: Idling with warm engine | - |
| EVAP Purge VSV | Purge VSV status: ON or OFF | OFF: Engine racing at 3000 rpm or more after warming up ON: Accelerator pedal released | - |
| Purge Cut VSV Duty | Purge cut VSV duty: Min.: 0%, Max.: 399.9% | - | - |
| Target Air-Fuel Ratio | Ratio compared to stoichiometric level: Min.: 0, Max.: 1.99 | 0.8 to 1.2: Idling with warm engine |
|
| AF Lambda B1S1 | Short-term fuel trim associated with bank 1 sensor 1: Min.: -0, Max.: 1.99 |
| - |
| AFS Voltage B1S1 | Air fuel ratio sensor output voltage for bank 1 sensor 1: Min.: 0 V, Max.: 7.99 V | 2.8 to 3.8 V: Idling | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technicians to check output voltage of sensor |
| AFS Current B1S1 | A/F sensor output current for bank 1 sensor 1: Min.: -128 mA, Max.: 127.99 mA | - | - |
| A/F Heater Duty #1 | Air fuel ratio sensor, heater duty ratio: for bank 1: Min.: 0%, Max.: 399.9% | 0 to 100% | - |
| O2S B1S2 | Heated oxygen sensor output voltage for bank 1 sensor 2: Min.: 0 V, Max.: 1.275 V | 0.1 to 0.9 V: Driving at 70 km/h (44 mph) | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technicians to check output voltage of sensor |
| O2 Heater B1S2 | Heated oxygen sensor heater (sensor 2): Not Act or Active | - | - |
| O2 Heater Curr Val B1S2 | Heated oxygen sensor current (sensor 2): Min.: 0 A, Max.: 4.9 A | - | - |
| Short FT #1 | Short-term fuel trim of bank 1: Min.: -100%, Max.: 99.2% | -20 to 20% | Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio |
| Long FT #1 | Long-term fuel trim of bank 1: Min.: -100%, Max.: 99.2% | -15 to 15% | Overall fuel compensation carried out in long-term to compensate for a continual deviation of short-term fuel trim from central value |
| Total FT #1 | Total fuel trim value for fuel system: Min.: -0.5, Max.: 0.496 | -0.2 to 0.2: Idling | - |
| Fuel System Status #1 | Fuel system status: OL or CL or OLDrive or OLFault or CLFault | CL: Idling after warming up |
|
| Fuel System Status #2 | - | Unused | - |
| IGN Advance | Ignition timing advance for No. 1 cylinder: Min.: -64 deg., Max.: 63.5 deg. | BTDC 5 to 15 deg.: Idling | - |
| Knock Feedback Value | Knock feedback value: Min.: -1024°CA, Max.: 1023.9°CA | -20 to 0 °CA: Driving at 70 km/h (44 mph) | - |
| Knock Correct Learn Value | Knock correction learning value: Min.: -1024°CA, Max.: 1023.9°CA | 0 to 20 CA: Driving at 70 km/h (44 mph) | - |
| Idle Spark Advn Ctrl #1 | Ignition timing advance value (for No. 1 cylinder): Min.: 0°CA, Max.: 15.93°CA | - | When the engine stalls, is difficult to start, or idles roughly |
| Idle Spark Advn Ctrl #2 | Ignition timing advance value (for No. 2 cylinder): Min.: 0°CA, Max.: 15.93°CA | - | When the engine stalls, is difficult to start, or idles roughly |
| Idle Spark Advn Ctrl #3 | Ignition timing advance value (for No. 3 cylinder): Min.: 0°CA, Max.: 15.93°CA | - | When the engine stalls, is difficult to start, or idles roughly |
| Idle Spark Advn Ctrl #4 | Ignition timing advance value (for No. 4 cylinder): Min.: 0°CA, Max.: 15.93°CA | - | When the engine stalls, is difficult to start, or idles roughly |
| VVT Control Status #1 | VVT control (bank 1) status: ON or OFF | - | - |
| VVT Advance Fail | Status of VVT advance fail: ON or OFF | ON: VVT control failure | - |
| VVT Aim Angle #1*2 | VVT aim angle (bank 1): Min.: 0%, Max.: 399.9% | 0 to 100% | VVT duty signal value during operation |
| VVT Change Angle #1*2 | VVT change angle (bank 1): Min.: 0 DegFR, Max.: 639.9 DegFR | 0 DegFR: Idling | Displacement angle during operation |
| VVT OCV Duty #1*2 | VVT oil control valve operation duty: Min.: 0%, Max.: 399.9% | 0 to 100% | Requested duty value for operation |
| VN Turbo Type | Variable nozzle turbo type: Not Avl or Commo or Vacuum or CAN Com | Not Avl (Unused) | - |
| Catalyst Temp B1S1 | Estimated catalyst temperature (bank 1, sensor 1): Min.: -40°C, Max.: 6513.5°C | - | - |
| Catalyst Temp B1S2 | Estimated catalyst temperature (bank 1, sensor 2): Min.: -40°C, Max.: 6513.5°C | - | - |
| Starter Signal | Starter switch (STSW) signal: Open or Close | Open: Starter signal on Close: Starter signal off | - |
| Power Steering Signal | Power steering signal: ON or OFF | ON: Power steering operation | - |
| Neutral Position SW Signal | Park/neutral position switch status: ON or OFF | ON: P or N position | - |
| Clutch Switch | Clutch switch: ON or OFF | - | - |
| Stop Light Switch | Stop light switch: ON or OFF | ON: Brake pedal depressed | - |
| A/C Signal | Air conditioning signal: ON or OFF | ON: Air conditioning on | - |
| Idle Up Signal | Idle up signal: ON or OFF | - | - |
| Closed Throttle Position SW | Closed throttle position switch: ON or OFF | ON: Throttle fully closed OFF: Throttle open | - |
| Fuel Cut Condition | Fuel cut determination flag: ON or OFF | ON: Any fuel cut operation executed | - |
| Check Mode | Check mode: ON or OFF | ON: Check mode on | Click here
|
| SPD Test Result | Check mode result for vehicle speed sensor: Compl or Incmpl | - | - |
| Misfire Test Result | Check mode result for misfire monitor: Compl or Incmpl | - | - |
| OXS1 Test Result | Check mode result for heated oxygen sensor: Compl or Incmpl | - | - |
| A/F Test Result #1 | Check mode result for air fuel ratio sensor: Compl or Incmpl | - | - |
| Complete Parts Monitor | Comprehensive component monitor: Not Avl or Avail | - | - |
| Fuel System Monitor | Fuel system monitor: Not Avl or Avail | - | - |
| Misfire Monitor | Misfire monitor: Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT monitor: Not Avl or Avail | - | - |
| EGR/VVT Monitor | EGR/VVT monitor: Compl or Incmpl | - | - |
| O2S (A/FS) Heater Monitor | O2S (A/FS) heater monitor: Not Avl or Avail | - | - |
| O2S (A/FS) Heater Monitor | O2S (A/FS) heater monitor: Compl or Incmpl | - | - |
| O2S (A/FS) Monitor | O2S (A/FS) monitor: Not Avl or Avail | - | - |
| O2S (A/FS) Monitor | O2S (A/FS) monitor: Compl or Incmpl | - | - |
| A/C Monitor | A/C Monitor: Not Avl or Avail | - | - |
| A/C Monitor | A/C Monitor: Compl or Incmpl | - | - |
| 2nd Air Monitor | 2nd Air Monitor: Not Avl or Avail | - | - |
| 2nd Air Monitor | 2nd Air Monitor: Compl or Incmpl | - | - |
| EVAP Monitor | EVAP Monitor: Not Avl or Avail | - | - |
| EVAP Monitor | EVAP Monitor: Compl or Incmpl | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor: Not Avl or Avail | - | - |
| Heated Catalyst Monitor | Heated catalyst monitor: Compl or Incmpl | - | - |
| Catalyst Monitor | Catalyst monitor: Not Avl or Avail | - | - |
| Catalyst Monitor | Catalyst monitor: Compl or Incmpl | - | - |
| TC Terminal | TC terminal status: ON or OFF | - | - |
| # Codes (Include History) | Number of codes: Min.: 0, Max.: 255 | - | Number of detected DTCs |
| MIL | MIL status: ON or OFF | ON: MIL on | - |
| MIL ON Run Distance | Distance traveled after MIL turned ON: Min.: 0 Km, Max.: 65535 Km | Distance since DTC detected | - |
| Running Time from MIL ON | Running time after MIL turned ON: Min.: 0 min, Max.: 65535 min | Equivalent to running time since MIL turned on | - |
| Time after DTC Cleared | Time since DTCs cleared: Min.: 0 min, Max.: 65535 min | Equivalent to time since DTCs cleared | - |
| Distance from DTC Cleared | Distance traveled after DTCs cleared: Min.: 0 km, Max.: 65535 km | Equivalent to distance driven since DTCs cleared | - |
| Warmup Cycle Cleared DTC | Warm-up cycles after DTCs cleared: Min.: 0, Max.: 255 | - | Number of warm-up cycles since DTCs cleared |
| Dist Batt Cable Disconnect | Distance driven after battery cable disconnected: Min.: 0 km, Max.: 65535 km | Total distance vehicle driven after battery cable disconnected | - |
| OBD Requirements | OBD requirements | E-OBD | - |
| Number of Emission DTC | Number of emission DTCs | - | Number of emission related DTCs |
| TC and TE1 | TC and CG (TE1) terminals of DLC3: ON or OFF | - | - |
| Ignition Trig. Count | Ignition counter: Min.: 0, Max.: 65535 | 0 to 400 | - |
| Cylinder #1 Misfire Count | Misfire count of cylinder 1: Min.: 0, Max.: 255 | 0 | - |
| Cylinder #2 Misfire Count | Misfire count of cylinder 2: Min.: 0, Max.: 255 | 0 | - |
| Cylinder #3 Misfire Count | Misfire count of cylinder 3: Min.: 0, Max.: 255 | 0 | - |
| Cylinder #4 Misfire Count | Misfire count of cylinder 4: Min.: 0, Max.: 255 | 0 | - |
| All Cylinders Misfire Count | Misfire count of all cylinders: Min.: 0, Max.: 255 | 0 to 35 | - |
| Misfire RPM | Engine speed when misfire occurs: Min.: 0 rpm, Max.: 6375 rpm | - | - |
| Misfire Load | Engine load when misfire occurred: Min.: 0 g/rev, Max.: 3.98 g/rev | - | - |
| Misfire Margin | Margin to detect engine misfire Min.: -128%, Max.: 127% | 0 to 99.22% | Misfire detection margin |
| Engine Speed (Starter Off) | Engine speed when starter off: Min.: 0 rpm, Max.: 51199 rpm | - | When the engine stalls, is difficult to start, or idles roughly |
| Starter Count | Number of times starter turned on after ignition switch turned from off to ON: Min.: 0, Max.: 255 | - | When the engine stalls, is difficult to start, or idles roughly |
| Run Dist of Previous Trip | Distance traveled during previous trip: Min.: 0 km, Max.: 655.35 km | - |
|
| Engine Starting Time | Engine run time (elapsed time from ignition switch ON to off): Min.: 0 ms, Max.: 655350 ms | - | When the engine stalls, is difficult to start, or idles roughly |
| Previous Trip Coolant Temp | Engine coolant temperature of previous trip: Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | When the engine stalls, is difficult to start, or idles roughly |
| Previous Trip Intake Temp | Intake temperature of previous trip:: Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | When the engine stalls, is difficult to start, or idles roughly |
| Engine Oil Temperature | Engine oil temperature (estimated): Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | When the engine stalls, is difficult to start, or idles roughly |
| Previous Trip Eng Oil Temp | Engine oil temperature of previous trip: Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | When the engine stalls, is difficult to start, or idles roughly |
| Ambient Temp for A/C | Ambient temperature: Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | When the engine stalls, is difficult to start, or idles roughly |
| Previous Trip Ambient Temp | Ambient temperature of previous trip: Min.: -40°C (-40°F), Max.: 215°C (419°F) | - | When the engine stalls, is difficult to start, or idles roughly |
| Engine Start Hesitation | History of instance of slow engine starts: ON or OFF | - | - |
| Low Rev for Eng Start | History of low engine speed after engine starts: ON or OFF | - | - |
| Minimum Engine Speed | Minimum engine speed: Min.: 0 rpm, Max.: 51199 rpm | - | When the engine stalls, is difficult to start, or idles roughly |
| Electric Fan Motor | Electric fan motor: ON or OFF | - | - |
| Idle Fuel Cut | Fuel cut idle: ON or OFF | ON: Fuel cut operating | Idle Fuel Cut = "ON" when throttle valve fully closed and engine speed over 2500 rpm |
| FC TAU | Fuel cut TAU (Fuel cut during very light load): ON or OFF | ON: Fuel cut operating | Fuel cut being performed during very light load to prevent incomplete engine combustion |
| Immobiliser Fuel Cut | Status of the immobiliser fuel cut: ON or OFF | - | - |
| Model Code | Identifies model code | ACV40 | - |
| Engine Type | Identifies engine type | 2AZFE | - |
| Cylinder Number | Identifies number of cylinders | 4 | - |
| Transmission Type | Identifies transmission type | M/T or ECT 5th | - |
| Destination | Identifies destination | W | - |
| Model Year | Identifies model year | 201# | - |
| System Identification | Identifies engine system | Gasoline | - |
| Engine Speed of Cyl #1 | Engine speed during No. 1 cylinder fuel cut: Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression performed using Active Test 51199 rpm: Active Test not performed |
| Engine Speed of Cyl #2 | Engine speed during No. 2 cylinder fuel cut: Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression performed using Active Test 51199 rpm: Active Test not performed |
| Engine Speed of Cyl #3 | Engine speed during No. 3 cylinder fuel cut: Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression performed using Active Test 51199 rpm: Active Test not performed |
| Engine Speed of Cyl #4 | Engine speed during No. 4 cylinder fuel cut: Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression performed using Active Test 51199 rpm: Active Test not performed |
| Av Engine Speed of All Cyl | Engine speed for all cylinders during fuel cut: Min.: 0 rpm, Max.: 51199 rpm | - | Output only when Check the Cylinder Compression performed using Active Test 51199 rpm: Active Test not performed |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the tester, perform the "Active Test".
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Injection Volume | Change injection volume | Between -12.5 and 24.8% |
|
| Control the Injection Volume for A/F Sensor | Change injection volume | Lowered by -12.5% or increased by 25% |
|
| Activate the VSV for Evap Control | Activate purge VSV control | ON/OFF | Only purge VSV is commanded during this test |
| Control the Fuel Pump / Speed | Activate fuel pump (C/OPN Relay) | ON/OFF | Test possible when following conditions met:
|
| Connect the TC and TE1 | Turn on and off TC and TE1 connection | ON/OFF |
|
| Control the Idle Fuel Cut Prohibit | Prohibit idling fuel cut control | ON/OFF | Test possible when following conditions met:
|
| Control the Electric Cooling Fan | Control electric cooling fan | ON/OFF | Test possible when following conditions met:
|
| Activate the Starter Relay | Starter | ON/OFF | Test possible when following conditions met:
|
| Activate the ACC Cut Relay | Activate ACC relay | ON/OFF | Test is possible when following conditions met:
|
| Control the ETCS Open/Close Slow Speed | Throttle actuator | Open/Close | Test possible when following conditions met:
|
| Control the ETCS Open/Close Fast Speed | Throttle actuator | Open/Close | Test possible when following conditions met:
|
| Control the VVT Linear (Bank 1) | Control the camshaft timing oil control valve assembly for intake camshaft (bank 1) | -128 to 127% This value added to present camshaft timing oil control valve assembly control duty 100%: Maximum advance -100%: Maximum retard |
|
| Control the VVT System (Bank 1) | Turn on and off the camshaft timing oil control valve assembly for intake camshaft (bank 1) | ON/OFF |
|
| Control the Cylinder #1 Fuel Cut | Cylinder No. 1 injector fuel cut | ON/OFF | Test possible during while vehicle stopped and engine idling. |
| Control the Cylinder #2 Fuel Cut | Cylinder No. 2 injector fuel cut | ON/OFF | Test possible during while vehicle stopped and engine idling. |
| Control the Cylinder #3 Fuel Cut | Cylinder No. 3 injector fuel cut | ON/OFF | Test possible during while vehicle stopped and engine idling. |
| Control the Cylinder #4 Fuel Cut | Cylinder No. 4 injector fuel cut | ON/OFF | Test possible during while vehicle stopped and engine idling. |
| Check the Cylinder Compression*1 | Check the cylinder compression pressure | ON/OFF | Fuel injection and ignition stopped in all cylinders. |