DTC P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) |
DTC P0012 Camshaft Position "A" - Timing Over-Retarded (Bank 1) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0011 | Advanced camshaft timing: With warm engine and engine speed of between 550 rpm and 4,000 rpm, all conditions (1), (2) and (3) are met (1 trip detection logic): 1. Difference between target and actual intake valve timings more than 5°CA (Crankshaft Angle) for 4.5 seconds 2. Current intake valve timing fixed (timing changes less than 5°CA in 5 seconds) 3. Variations in VVT controller timing more than 19°CA of maximum delayed timing (malfunction in advance timing) |
|
| P0012 | Retarded camshaft timing: With warm engine and engine speed of between 550 rpm and 4,000 rpm, all conditions (1), (2) and (3) are met (2 trip detection logic): 1. Difference between target and actual intake valve timings more than 5°CA (Crankshaft Angle) for 4.5 seconds 2. Current intake valve timing fixed (timing changes less than 5°CA in 5 seconds) 3. Variations in VVT controller timing 19°CA or less of maximum delayed timing (malfunction in retarded timing) |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011 OR P0012) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P0011 or P0012 | A |
| P0011 or P0012 and other DTCs | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OCV) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Warm up the engine.
Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1).
Check the engine speed while operating the Oil Control Valve (OCV) using the tester.
| Tester Operation | Specified Condition |
| OCV OFF | Normal engine speed |
| OCV ON | Engine idles roughly or stalls (soon after OCV switched from OFF to ON) |
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Clear the DTCs (Click here ).
Start the engine and warm it up.
Switch the ECM from normal mode to check mode using the tester.
Drive the vehicle for more than 10 minutes.
Read the DTCs using the tester.
|
| ||||
| OK | ||
| ||
| 4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN) |
![]() |
Remove the cylinder head cover.
Turn the crankshaft pulley, and align its groove with the timing mark "0" on the timing chain cover.
Check that the timing marks on the camshaft timing sprocket and camshaft timing gear are facing upward as shown in the illustration.
Reinstall the cylinder head cover.
|
| ||||
| OK | |
| 5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (OCV) |
![]() |
Remove the OCV.
Measure the resistance between the terminals of the OCV.
![]() |
Apply positive battery voltage to terminal 1 and negative battery voltage to terminal 2. Check the valve operation.
Reinstall the OCV.
|
| ||||
| OK | |
| 6.INSPECT OIL CONTROL VALVE FILTER |
![]() |
Remove the OCV filter.
Check that the filter is not clogged.
Reinstall the OCV filter.
|
| ||||
| OK | |
| 7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY |
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Clear the DTCs (Click here).
Start the engine and warm it up.
Switch the ECM from normal mode to check mode using the tester.
Drive the vehicle for more than 10 minutes.
Read the output DTCs using the tester.
|
| ||||
| OK | ||
| ||