DTC P0115 Engine Coolant Temperature Circuit Malfunction |
DTC P0117 Engine Coolant Temperature Circuit Low Input |
DTC P0118 Engine Coolant Temperature Circuit High Input |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0115 | Open or short in engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| P0117 | Short in engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| P0118 | Open in engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic) |
|
| Temperature Displayed | Malfunction |
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) | Short circuit |

| 1.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Read the value displayed on the tester.
| Result | Proceed to |
| Displayed temperature is -40°C (-40°F) | A |
| Displayed temperature is 140°C (284°F) | B |
| Same as actual engine coolant temperature | C |
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS) |
Confirm good connection at the engine coolant temperature sensor connector.

| *1 | Engine Coolant Temperature Sensor | *2 | ECM |
| *3 | Front view of wire harness connector (to Engine Coolant Temperature Sensor) | - | - |
Disconnect the engine coolant temperature sensor connector.
Connect terminals 1 and 2 of the engine coolant temperature sensor connector on the wire harness side.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Read the value displayed on the tester.
Reconnect the engine coolant temperature sensor connector.
|
| ||||
| OK | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) |
Disconnect the engine coolant temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C4-2 - C24-97 (THW) | Always | Below 1 Ω |
| C4-1 - C24-96 (ETHW) | Always | Below 1 Ω |
Reconnect the engine coolant temperature sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS) |
![]() |
Disconnect the engine coolant temperature sensor connector.
| *1 | Engine Coolant Temperature Sensor |
| *2 | ECM |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Read the value displayed on the tester.
Reconnect the engine coolant temperature sensor connector.
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) |
Disconnect the engine coolant temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C4-2 or C24-97 (THW) - Body ground | Always | 10 kΩ or higher |
Reconnect the engine coolant temperature sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||