DTC P0120 Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction |
DTC P0121 Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem |
DTC P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input |
DTC P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input |
DTC P0220 Throttle / Pedal Position Sensor / Switch "B" Circuit |
DTC P0222 Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input |
DTC P0223 Throttle / Pedal Position Sensor / Switch "B" Circuit High Input |
DTC P2135 Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0120 | Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds (1 trip detection logic) |
|
| P0121 | Difference between VTA1 and VTA2 voltages less than 0.8 V, or more than 1.6 V for 2 seconds (1 trip detection logic) |
|
| P0122 | Output voltage of VTA1 0.2 V or less for 2 seconds (1 trip detection logic) |
|
| P0123 | Output voltage of VTA1 4.535 V or more for 2 seconds (1 trip detection logic) |
|
| P0220 | Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds (1 trip detection logic) |
|
| P0222 | Output voltage of VTA2 1.75 V or less for 2 seconds (1 trip detection logic) |
|
| P0223 | Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 2.02 V for 2 seconds (1 trip detection logic) |
|
| P2135 | Either condition (a) or (b) is met (1 trip detection logic): (a) Difference between output voltages of VTA1 and VTA2 0.02 V or less for 0.5 seconds or more (b) Output voltage of VTA1 0.2 V or less, and VTA2 1.75 V or less for 0.4 seconds or more |
|
| Tester Display | Accelerator Pedal Fully Released | Accelerator Pedal Fully Depressed |
| Throttle Position No. 1 | 0.5 to 1.1 V | 3.2 to 4.8 V |
| Throttle Position No. 2 | 2.1 to 3.1 V | 4.6 to 5.0 V |

| 1.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1 and Throttle Position No. 2.
Read the values displayed on the tester.
| When Accelerator Pedal Released | When Accelerator Pedal Fully Depressed | Trouble Area | Proceed to | ||
| Throttle Position No. 1 | Throttle Position No. 2 | Throttle Position No. 1 | Throttle Position No. 2 | ||
| 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | VC circuit open | A |
| 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V | E2 circuit open | |
| 0 to 0.2 V, or 4.5 to 5.0 V | 2.1 V to 3.1 V (Fail-safe) | 0 to 0.2 V, or 4.5 to 5.0 V | 2.1 V to 3.1 V (Fail-safe) | VTA1 circuit open or ground short | |
| 0.6 V to 1.4 V (Fail-safe) | 0 to 0.2 V, or 4.5 to 5.0 V | 0.6 V to 1.4 V (Fail-safe) | 0 to 0.2 V, or 4.5 to 5.0 V | VTA2 circuit open or ground short | |
| 0.5 to 1.1 V | 2.1 to 3.1 V | 3.2 to 4.8 V (Not fail-safe) | 4.6 to 5.0 V (Not fail-safe) | Throttle position sensor circuit normal | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM) |
Disconnect the throttle position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C5-5 (VC) - C24-67 (VCTA) | Always | Below 1 Ω |
| C5-6 (VTA) - C24-115 (VTA1) | Always | Below 1 Ω |
| C5-4 (VTA2) - C24-114 (VTA2) | Always | Below 1 Ω |
| C5-3 (E2) - C24-91 (ETA) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| C5-5 (VC) or C24-67 (VCTA) - Body ground | Always | 10 kΩ or higher |
| C5-6 (VTA) or C24-115 (VTA1) - Body ground | Always | 10 kΩ or higher |
| C5-4 (VTA2) or C24-114 (VTA2) - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the throttle position sensor connector.
|
| ||||
| OK | |
| 3.INSPECT ECM (VC VOLTAGE) |
![]() |
Disconnect the throttle position sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C5-5 (VC) - C5-3 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| *1 | Front view of wire harness connector (to Throttle Position Sensor) |
Reconnect the throttle position sensor connector.
|
| ||||
| OK | |
| 4.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY |
Replace the throttle with motor body assembly (Click here).
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0120, P0121, P0122, P0123, P0220, P0222, P0223 and/or P2135 are output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||