DTC P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) |
DTC P0038 Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0037 | Heated Oxygen (HO2) sensor heater current less than 0.3 A (1 trip detection logic) |
|
| P0038 | Heated Oxygen (HO2) sensor heater current more than 2 A (1 trip detection logic) |
|
| 1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the C22 Heated Oxygen (HO2) sensor connector.
Measure the resistance between the terminals of the HO2 sensor connector.
| Tester Connection | Specified Condition |
| HT1B (1) - +B (2) | 11 to 16 Ω at 20°C (68°F) |
| HT1B (1) - E2 (4) | 10 kΩ or higher |
Reconnect the HO2 sensor connector.
|
| ||||
| OK | |
| 2.CHECK TERMINAL VOLTAGE (+B OF HO2 SENSOR) |
![]() |
Disconnect the C22 HO2 sensor connector.
Turn the ignition switch to the ON position.
Measure the voltage between the terminal of the C22 HO2 sensor connector and body ground.
| Tester Connection | Specified Condition |
| +B (C22-2) - Body ground | 9 to 14 V |
Reconnect the HO2 sensor connector.
|
| ||||
| NG | |
| 3.INSPECT ENGINE ROOM J/B (EFI RELAY, EFI MAIN FUSE) |
![]() |
Inspect the EFI MAIN fuse.
Remove the EFI MAIN fuse from the engine room J/B.
Measure the EFI MAIN fuse resistance.
Reinstall the EFI MAIN fuse.
Inspect the EFI relay.
Remove the engine room J/B from the engine room R/B.
Measure the EFI relay resistance.
| Tester Connection | Specified Condition |
| 1E-6 - 1E-12 | 10 kΩ or higher |
| Below 1 Ω (Apply battery voltage between terminals 1E-9 and 1E-11) |
Reinstall the engine room J/B.
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - EFI RELAY) |
![]() |
Inspect the EFI No. 3 fuse.
Remove the EFI No. 3 fuse from the engine room J/B.
Measure the EFI No. 3 fuse resistance.
Reinstall the EFI No. 3 fuse.
Disconnect the C22 HO2 sensor connector.
Remove the engine room J/B from the engine room R/B.
Disconnect the 1E engine room J/B connector.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| +B (C22-2) - Engine room J/B (1E-6) | Below 1 Ω |
| Tester Connection | Specified Condition |
| +B (C22-2) or Engine room J/B (1E-6) - Body ground | 10 kΩ or higher |
Reconnect the HO2 sensor connector.
Reconnect the engine room J/B connector.
Reinstall the engine room J/B.
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - ECM) |
![]() |
Disconnect the C22 HO2 sensor connector.
Disconnect the C24 ECM connector.
Measure the resistance between the terminals of the wire harness side connectors.
| Tester Connection | Specified Condition |
| HT1B (C22-1) - HT1B (C24-47) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HT1B (C22-1) or HT1B (C24-47) - Body ground | 10 kΩ or higher |
Reconnect the HO2 sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 6.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Clear the DTCs (Click here).
Start the engine.
Allow the engine to idle for 2 minutes or more.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| No output | A |
| P0037 or P0038 | B |
|
| ||||
| A | ||
| ||