DTC P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit |
DTC P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input |
DTC P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input |
DTC P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit |
DTC P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input |
DTC P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input |
DTC P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2120 | VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic) |
|
| P2122 | VPA is 0.4 V or less for 0.5 seconds or more when accelerator pedal is fully released (1 trip detection logic) |
|
| P2123 | VPA is 4.8 V or more for 2.0 seconds or more (1 trip detection logic) |
|
| P2125 | VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic) |
|
| P2127 | VPA2 is 1.2 V or less for 0.5 seconds or more when accelerator pedal is fully released (1 trip detection logic) |
|
| P2128 | Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic): (a) VPA2 is 4.8 V or more (b) VPA is between 0.4 V and 3.45 V |
|
| P2138 | Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA and VPA2 is 0.02 V or less (b) VPA is 0.4 V or less and VPA2 is 1.2 V or less |
|
| Trouble Area | ACCEL POS #1 When AP Released | ACCEL POS #2 When AP Released | ACCEL POS #1 When AP Depressed | ACCEL POS #2 When AP Depressed |
| VCP circuit open | 0 to 0.4 V | 0 to 1.2 V | 0 to 0.4 V | 0 to 1.2 V |
| Open or ground short in VPA circuit | 0 to 0.4 V | 1.2 to 2.0 V | 0 to 0.4 V | 3.4 to 5.0 V |
| Open or ground short in VPA2 circuit | 0.5 to 1.1 V | 0 to 0.2 V | 2.6 to 4.5 V | 0 to 0.2 V |
| EPA circuit open | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V |
| Normal condition | 0.5 to 1.1 V | 1.2 to 2.0 V | 2.6 to 4.5 V | 3.4 to 5.0 V |

| 1.READ VALUE USING INTELLIGENT TESTER (ACCEL POS #1 AND ACCEL POS #2) |
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.
Read the value displayed on the tester.
| Accelerator Pedal Operation | ACCEL POS #1 (AP#1) | ACCEL POS #2 (AP#2) |
| Released | 0.5 to 1.1 V | 1.2 to 2.0 V |
| Depressed | 2.6 to 4.5 V | 3.4 to 5.0 V |
|
| ||||
| NG | |
| 2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
![]() |
Disconnect the A17 Accelerator Pedal Position (APP) sensor connector.
Disconnect the A24 (RHD) or A55 (LHD) ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| VPA (A17-6) - VPA (A24-55) | Below 1 Ω |
| EPA (A17-5) - EPA (A24-59) | Below 1 Ω |
| VCPA (A17-4) - VCPA (A24-57) | Below 1 Ω |
| VPA2 (A17-3) - VPA2 (A24-56) | Below 1 Ω |
| EPA2 (A17-2) - EPA2 (A24-60) | Below 1 Ω |
| VCP2 (A17-1) - VCP2 (A24-58) | Below 1 Ω |
| Tester Connection | Specified Condition |
| VPA (A17-6) - VPA (A55-55) | Below 1 Ω |
| EPA (A17-5) - EPA (A55-59) | Below 1 Ω |
| VCPA (A17-4) - VCPA (A55-57) | Below 1 Ω |
| VPA2 (A17-3) - VPA2 (A55-56) | Below 1 Ω |
| EPA2 (A17-2) - EPA2 (A55-60) | Below 1 Ω |
| VCP2 (A17-1) - VCP2 (A55-58) | Below 1 Ω |
| Tester Connection | Specified Condition |
| VPA (A17-6) or VPA (A24-55) - Body ground | 10 kΩ or higher |
| EPA (A17-5) or EPA (A24-59) - Body ground | 10 kΩ or higher |
| VCPA (A17-4) or VCPA (A24-57) - Body ground | 10 kΩ or higher |
| VPA2 (A17-3) or VPA2 (A24-56) - Body ground | 10 kΩ or higher |
| EPA2 (A17-2) or EPA2 (A24-60) - Body ground | 10 kΩ or higher |
| VCP2 (A17-1) or VCP2 (A24-58) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| VPA (A17-6) or VPA (A55-55) - Body ground | 10 kΩ or higher |
| EPA (A17-5) or EPA (A55-59) - Body ground | 10 kΩ or higher |
| VCPA (A17-4) or VCPA (A55-57) - Body ground | 10 kΩ or higher |
| VPA2 (A17-3) or VPA2 (A55-56) - Body ground | 10 kΩ or higher |
| EPA2 (A17-2) or EPA2 (A55-60) - Body ground | 10 kΩ or higher |
| VCP2 (A17-1) or VCP2 (A55-58) - Body ground | 10 kΩ or higher |
Reconnect the APP sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.INSPECT ACCELERATOR POSITION SENSOR (VCPA AND VCP2 VOLTAGE) |
![]() |
Disconnect the A17 APP sensor connector.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| VCPA (A17-4) - EPA (A17-5) | 4.5 to 5.0 V |
| VCP2 (A17-1) - EPA2 (A17-2) | 4.5 to 5.0 V |
Reconnect the APP sensor connector.
|
| ||||
| OK | |
| 4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY |
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Clear the DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138 | A |
| No output | B |
|
| ||||
| A | ||
| ||