DTC P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2121 | Difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V for 0.5 seconds (1 trip detection logic) |
|
| 1.READ VALUE USING INTELLIGENT TESTER (ACCEL POS #1 AND ACCEL POS #2) |
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / Accelerator Position No. 1 and Accelerator Position No. 2.
Read the values displayed on the tester.
| Accelerator Pedal Operation | ACCEL POS #1 (AP#1) | ACCEL POS #2 (AP#2) |
| Released | 0.5 to 1.1 V | 1.2 to 2.0 V |
| Depressed | 2.6 to 4.5 V | 3.4 to 5.0 V |
|
| ||||
| NG | |
| 2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
![]() |
Disconnect the A17 Accelerator Pedal Position (APP) sensor connector.
Disconnect the A24 (RHD) or A55 (LHD) ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| VPA (A17-6) - VPA (A24-55) | Below 1 Ω |
| EPA (A17-5) - EPA (A24-59) | Below 1 Ω |
| VCPA (A17-4) - VCPA (A24-57) | Below 1 Ω |
| VPA2 (A17-3) - VPA2 (A24-56) | Below 1 Ω |
| EPA2 (A17-2) - EPA2 (A24-60) | Below 1 Ω |
| VCP2 (A17-1) - VCP2 (A24-58) | Below 1 Ω |
| Tester Connection | Specified Condition |
| VPA (A17-6) - VPA (A55-55) | Below 1 Ω |
| EPA (A17-5) - EPA (A55-59) | Below 1 Ω |
| VCPA (A17-4) - VCPA (A55-57) | Below 1 Ω |
| VPA2 (A17-3) - VPA2 (A55-56) | Below 1 Ω |
| EPA2 (A17-2) - EPA2 (A55-60) | Below 1 Ω |
| VCP2 (A17-1) - VCP2 (A55-58) | Below 1 Ω |
| Tester Connection | Specified Condition |
| VPA (A17-6) or VPA (A24-55) - Body ground | 10 kΩ or higher |
| EPA (A17-5) or EPA (A24-59) - Body ground | 10 kΩ or higher |
| VCPA (A17-4) or VCPA (A24-57) - Body ground | 10 kΩ or higher |
| VPA2 (A17-3) or VPA2 (A24-56) - Body ground | 10 kΩ or higher |
| EPA2 (A17-2) or EPA2 (A24-60) - Body ground | 10 kΩ or higher |
| VCP2 (A17-1) or VCP2 (A24-58) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| VPA (A17-6) or VPA (A55-55) - Body ground | 10 kΩ or higher |
| EPA (A17-5) or EPA (A55-59) - Body ground | 10 kΩ or higher |
| VCPA (A17-4) or VCPA (A55-57) - Body ground | 10 kΩ or higher |
| VPA2 (A17-3) or VPA2 (A55-56) - Body ground | 10 kΩ or higher |
| EPA2 (A17-2) or EPA2 (A55-60) - Body ground | 10 kΩ or higher |
| VCP2 (A17-1) or VCP2 (A55-58) - Body ground | 10 kΩ or higher |
Reconnect the APP sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY |
| NEXT | |
| 4.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Clear the DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P2121 | A |
| No output | B |
|
| ||||
| A | ||
| ||