Home › BODY ELECTRICAL › WIPER AND WASHER › WIPER AND WASHER SYSTEM

WIPER AND WASHER SYSTEM > Wiper and Washer Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit detects the state of the windshield wiper switch assembly (wiper and washer switch) and sends it to the windshield wiper relay assembly (auto wiper relay).

WIRING DIAGRAM


E119089E02


E119096E01


INSPECTION PROCEDURE

1.CHECK WINDSHIELD WIPER SWITCH ASSEMBLY (WIPER SWITCH AND WASHER SWITCH)


  1. Remove the windshield wiper switch assembly.


    E119090E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Except Hong Kong, India and LHD:
    Tester Connection
    Switch Connection
    Specified Condition
    E20-2 (+B) - E20-4 (+2)
    HI
    Below 1 Ω
    E20-3 (+1) - E20-2 (+B)
    MIST
    LO
    E20-3 (+1) - E20-1 (+S)
    OFF
    E20-9 (AUTO) - E20-10 (E)
    AUTO
    E20-7 (VR1) - E20-8 (VR2)
    Adjusting ring changed from (+) side to (-) side
    0 to 2.7 kΩ
    Hong Kong, India:
    Tester Connection
    Switch Condition
    Specified Condition
    E20-2 (+1) - E20-3 (+B)
    MIST
    Below 1 Ω
    LO
    E20-2 (+1) - E20-4 (+S)
    OFF
    E20-3 (+B) - E20-5 (E)
    HI
    E20-6 (AUTO) - E20-5 (E)
    AUTO
    E20-7 (VR2) - E20-8 (VR1)
    Adjusting ring changed from (+) side to (-) side
    0 to 2.7 kΩ



NG
REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY
OK


2.CHECK HARNESS AND CONNECTOR (WIPER SWITCH - AUTO WIPER RELAY, BODY GROUND)


    E119091E01
  1. Disconnect the E20 windshield wiper switch assembly connector.

  1. Disconnect the E26 auto wiper relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Except Hong Kong, India and LHD:
    Tester Connection
    Condition
    Specified Condition
    E20-1 (+S) - E26-11 (+SSW)
    Always
    Below 1 Ω
    E20-1 (+S) - Body ground
    Always
    10 kΩ or higher
    E20-2 (+B) - E26-12 (IG)
    Always
    Below 1 Ω
    E20-2 (+B) - Body ground
    Always
    10 kΩ or higher
    E20-3 (+1) - E26-1 (+2S)
    Always
    Below 1 Ω
    E20-3 (+1) - Body ground
    Always
    10 kΩ or higher
    E20-4 (+2) - E26-3 (+2)
    Always
    Below 1 Ω
    E20-4 (+2) - Body ground
    Always
    10 kΩ or higher
    E20-7 (VR1) - E26-7 (VR1)
    Always
    Below 1 Ω
    E20-7 (VR1) - Body ground
    Always
    10 kΩ or higher
    E20-8 (VR2) - E26-6 (VR2)
    Always
    Below 1 Ω
    E20-8 (VR2) - Body ground
    Always
    10 kΩ or higher
    E20-9 (AUTO) - E26-17 (C1)
    Always
    Below 1 Ω
    E20-9 (AUTO) - Body ground
    Always
    10 kΩ or higher
    E20-10 (E) - E26-16 (C0)
    Always
    Below 1 Ω
    E20-10 (E) - Body ground
    Always
    Below 1 Ω
    Hong Kong, India:
    Tester Connection
    Condition
    Specified Condition
    E20-1 (+2) - E26-3 (+2)
    Always
    Below 1 Ω
    E20-1 (+2) - Body ground
    Always
    10 kΩ or higher
    E20-2 (+1) - E26-1 (+2S)
    Always
    Below 1 Ω
    E20-2 (+1) - Body ground
    Always
    10 kΩ or higher
    E20-3 (+B) - E26-12 (IG)
    Always
    Below 1 Ω
    E20-3 (+B) - Body ground
    Always
    10 kΩ or higher
    E20-4 (+S) - E26-11 (+SSW)
    Always
    Below 1 Ω
    E20-4 (+S) - Body ground
    Always
    10 kΩ or higher
    E20-5 (E) - E26-16 (C0)
    Always
    Below 1 Ω
    E20-5 (E) - Body ground
    Always
    Below 1 Ω
    E20-6 (AUTO) - E26-17 (C1)
    Always
    Below 1 Ω
    E20-6 (AUTO) - Body ground
    Always
    10 kΩ or higher
    E20-7 (VR2) - E26-6 (VR2)
    Always
    Below 1 Ω
    E20-7 (VR2) - Body ground
    Always
    10 kΩ or higher
    E20-8 (VR1) - E26-7 (VR1)
    Always
    Below 1 Ω
    E20-8 (VR1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE