Home › CRUISE CONTROL SYSTEM › CRUISE CONTROL › CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM > Cruise Control Switch Circuit

for Preparation Click here


DESCRIPTION

The cruise control main switch operates 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP, and CANCEL. The SET, TAP-DOWN, and - (COAST) functions, and the RES (RESUME), TAP-UP, and + (ACCEL) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact point of the cruise control main switch is turned on with the switch operation. Then the ECM reads the voltage value that has been changed by the switch operation to control SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL.

WIRING DIAGRAM


E135409E04


INSPECTION PROCEDURE

1.READ VALUE ON INTELLIGENT TESTER
E107091E05
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester main switch on.

  1. Check the DATA LIST for proper functioning of the cruise control main switch.

    ECM (Cruise control): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Main SW M-CPU
    Main switch signal (Main CPU) / ON or OFF
    ON: Cruise control main switch on
    OFF: Cruise control main switch off
    -
    Cancel Switch
    CANCEL switch signal / ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    SET/COAST Switch
    SET/COAST switch signal / ON or OFF
    ON: - (COAST)/SET switch on
    OFF: - (COAST)/SET switch off
    -
    RES/ACC Switch
    RES / ACC switch signal / ON or OFF
    ON: + (ACCEL)/RES (RESUME) switch on
    OFF: + (ACCEL)/RES (RESUME) switch off
    -
    Main SW S-CPU
    Main switch signal (Sub CPU) / ON or OFF
    ON: Cruise control main switch on
    OFF: Cruise control main switch off
    -

    OK:
    When the cruise control main switch is operated, the display changes as shown above.
    Result 
    Result
    Proceed to
    OK
    A
    NG (All items are defective)
    B
    NG (1 to 4 items are defective)
    C



B
Go to step 2

C
REPLACE CRUISE CONTROL MAIN SWITCH (Click here)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT CRUISE CONTROL MAIN SWITCH
  1. Remove the cruise control main switch (Click here).



  1. Measure the resistance according to the value(s) in the table below.


    E106137E06


Standard resistance:

Tester Connection
Switch Condition
Specified Condition
A-1 (CCS) - A-3 (ECC)
Neutral
10 kΩ or higher
+ (ACCEL)/RES (RESUME)
216 to 264 Ω
- (COAST)/SET
567 to 693 Ω
CANCEL
1,386 to 1,694 Ω
Main Switch on
Below 1 Ω



NG
REPLACE CRUISE CONTROL MAIN SWITCH (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (CRUISE CONTROL MAIN SWITCH - SPIRAL CABLE)
E103330E03
  1. Disconnect the b1 connector from the spiral cable.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A-1 - b1-3
    Always
    Below 1 Ω
    A-3 - b1-4
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK SPIRAL CABLE
E106780E15

NOTICE:
The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the page shown in the brackets.

HINT:
  1. Removal (Click here)
  2. Installation (Click here)

  1. Remove the spiral cable.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Spiral Cable Position
    Specified Condition
    b1-3 - E18-1 (CCS)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    b1-4 - E18-2 (ECC)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

HINT:
The spiral cable makes a maximum of approximately 5 rotations.



NG
REPLACE SPIRAL CABLE (Click here)
OK


5.CHECK WIRE HARNESS (SPIRAL CABLE - ECM AND BODY GROUND)


    E135383E17
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E18-1 - A55-40 (CCS)*1
    E18-1 - A24-40 (CCS)*2
    Always
    Below 1 Ω
    A55-40 (CCS) - Body ground*1
    A24-40 (CCS) - Body ground*2
    Always
    10 kΩ or higher
    E18-2 (ECC) - Body ground
    Always
    Below 1 Ω

    HINT:
    *1: 2GR-FE (LHD)
    *2: 2AZ-FE, 2GR-FE (RHD)

Result:
Result
Proceed to
NG
A
OK (for 2AZ-FE)
B
OK (for 2GR-FE)
C



B
REPLACE ECM (2AZ-FE) (Click here)

C
REPLACE ECM (2GR-FE) (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR