TOYOTA PARKING ASSIST-SENSOR SYSTEM > TERMINALS OF ECU |
| CHECK CLEARANCE WARNING ECU |
Disconnect the O28 ECU connector.

Measure the resistance and voltage between each terminal of the wire harness side connector.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| O28-12 (CLSW) - O28-17 (E) | B - W-B | Clearance sonar main switch signal | Ignition switch off | Below 1 V |
| Ignition switch ON, clearance sonar main switch ON | 11 to 14 V | |||
| O28-15 (IG) - O28-17 (E) | R - W-B | IG signal / IG power source signal | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V | |||
| O28-17 (E) - Body ground | W-B - Body ground | ECU ground | Always | Below 1 Ω |
Reconnect the O28 ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| O28-7 (BOR) - O28-17 (E) | V - W-B | Rear sensor circuit power source | Ignition switch off | Below 1 V |
| Ignition switch ON Clearance sonar main switch on | 7.2 to 8.8 V | |||
| O28-9 (SOF) - O28-17 (E) | BR - W-B | Front sensor communication signal | Ignition switch ON Clearance sonar main switch on Shift lever in R | Waveform 2 |
| O28-10 (BBZ) - O28-17 (E) | R - W-B | Clearance warning buzzer signal | Ignition switch off | Below 1 V |
| Ignition switch ON Clearance sonar main switch on | 11 to 14 V | |||
| O28-11 (EF) - O28-17 (E) | O - W-B | Ground for clearance warning buzzer | Buzzer sounding | Waveform 1 |
| O28-19 (E1) - O28-17 (E) | L - W-B | Front sensor circuit ground | Always | Below 1 Ω |
| O28-18 (E2) - O28-17 (E) | G - W-B | Rear sensor circuit ground | Always | Below 1 Ω |
| O28-21 (BOF) - O28-17 (E) | W - W-B | Front sensor circuit power source | Ignition switch off | Below 1 V |
| Ignition switch ON Clearance sonar main switch on | 7.2 to 8.8 V | |||
| O28-24 (SOR) - O28-17 (E) | R - W-B | Rear sensor communication signal | Ignition switch ON Clearance sonar main switch on Shift lever in R | Waveform 2 |
Using an oscilloscope, check waveform 1.
![]() |
Waveform 1 (Reference)
| Item | Content |
| Terminal No. (Symbols) | O28-11 (EF) - O28-17 (E) |
| Tool Setting | 2 V/DIV., 500 μsec./DIV. |
| Vehicle Condition | When sonar detects obstacle (buzzer sounds) |
Using an oscilloscope, check waveform 2.
![]() |
Waveform 2 (Reference)
| Item | Content |
| Terminal No. (Symbols) |
|
| Tool Setting | 5 V/DIV., 1 msec./DIV. |
| Condition | Ignition switch ON, clearance sonar main switch on, shift lever in R |