Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System)

DTC    B2799    Engine Immobiliser System Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when one of the following occurs: 1) the ECM detects an error in its own communication with the ID code box (immobiliser code ECU); 2) the ECM detects an error in the communication lines; or 3) the ECU communication ID between the ID code box (immobiliser code ECU) and ECM is different and an engine start is attempted.

HINT:
Before troubleshooting this DTC, make sure that no certification ECU (smart key ECU assembly) DTCs are present. If present, troubleshoot the certification ECU (smart key ECU assembly) DTCs first.


DTC Code
DTC Detection Condition
Trouble Area
B2799
One of the following conditions is met:
  1. Error in communication between ECM and ID code box (immobiliser code ECU)
  2. Error in communication lines
  3. Communication ID is different between ID code box (immobiliser code ECU) and ECM during communication
  1. Wire harness or connector
  2. ECM
  3. ID code box (immobiliser code ECU)

WIRING DIAGRAM


B219229E01


INSPECTION PROCEDURE

NOTICE:
  1. If the ID code box (immobiliser code ECU) is replaced, register the ECU code and ECU communication ID.
  2. If the ECM is replaced, register the ECU communication ID.

1.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    OK:
    B2799 output does not recur.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.RE-REGISTER ECU COMMUNICATION ID
  1. Re-register the ECU communication ID.


NEXT


3.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    OK:
    B2799 output does not recur.



NG
Go to step 4
OK

END (ECU COMMUNICATION ID WAS INCORRECT) 

4.CHECK CONNECTOR CONNECTION CONDITION
  1. Turn the engine switch off.

  1. Check that the connectors are properly connected to the ECM and ID code box (immobiliser code ECU).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


5.CHECK HARNESS AND CONNECTOR (ID CODE BOX - ECM)
  1. Disconnect the ID code box (immobiliser code ECU) connector.



  1. Disconnect the ECM connector.


    B150861E27

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    E68-5 (EFII) - A24-10 (IMO)
    Always
    Below 1 Ω
    E68-6 (EFIO) - A24-11 (IMI)
    Always
    Below 1 Ω
    E68-5 (EFII) - Body ground
    Always
    10 kΩ or higher
    E68-6 (EFIO) - Body ground
    Always
    10 kΩ or higher
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    E68-5 (EFII) - A55-10 (IMO)
    Always
    Below 1 Ω
    E68-6 (EFIO) - A55-11 (IMI)
    Always
    Below 1 Ω
    E68-5 (EFII) - Body ground
    Always
    10 kΩ or higher
    E68-6 (EFIO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


7.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.


NEXT


8.CHECK DTC OUTPUT
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs (Click here).

    OK:
    B2799 output does not recur.



NG
REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
OK

END (ECM WAS DEFECTIVE)