DTC P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor) |
DTC P0328 Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor) |
DTC P0332 Knock Sensor 2 Circuit Low Input (Bank 2) |
DTC P0333 Knock Sensor 2 Circuit High Input (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0327 P0332 | Output voltage of knock sensor 1 or 2 is 0.5 V or less (1 trip detection logic) |
|
| P0328 P0333 | Output voltage of knock sensor 1 or 2 is 4.5 V or more (1 trip detection logic) |
|

| Item | Content |
| Terminals | KNK1 - EKNK or KNK2 -EKN2 |
| Equipment Settings | 0.01 to 10 V/DIV. 0.01 to 10 ms./DIV. |
| Condition | Keep engine speed at 4,000 rpm with warm engine |

| 1.READ OUTPUT DTC (CHECK KNOCK SENSOR CIRCUIT) |
![]() |
Disconnect the CV1 connector.
Using lead wires, connect the connectors as follows:
| Male Connector - Female Connector |
| Terminal 2 - Terminal 4 |
| Terminal 1 - Terminal 3 |
| Terminal 4 - Terminal 2 |
| Terminal 3 - Terminal 1 |
Warm up the engine.
Run the engine at 3,000 rpm for 10 seconds or more.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Display | Proceed to |
| DTCs same as when vehicle brought in P0327, P0328 → P0327, P0328 or P0332, P0333 → P0332, P0333 | A |
| DTCs different from when vehicle brought in P0327, P0328 → P0332, P0333 or P0332, P0333 → P0327, P0328 | B |
Reconnect the CV1 connector.
|
| ||||
| A | |
| 2.CHECK WIRE HARNESS AND CONNECTOR (CONNECTOR - ECM) |
![]() |
Disconnect the CV1 connector.
Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| CV1 female connector 2 - KNK1 (C58-95) | Below 1 Ω |
| CV1 female connector 1 - EKNK (C58-94) | Below 1 Ω |
| CV1 female connector 4 - KNK2 (C58-118) | Below 1 Ω |
| CV1 female connector 3 - EKN2 (C58-117) | Below 1 Ω |
| Tester Connection | Specified Condition |
| CV1 female connector 2 - KNK1 (C55-95) | Below 1 Ω |
| CV1 female connector 1 - EKNK (C55-94) | Below 1 Ω |
| CV1 female connector 4 - KNK2 (C55-118) | Below 1 Ω |
| CV1 female connector 3 - EKN2 (C55-117) | Below 1 Ω |
| Tester Connection | Specified Condition |
| CV1 female connector 2 or KNK1 (C58-95) - Body ground | 10 kΩ or higher |
| CV1 female connector 1 or EKNK (C58-94) - Body ground | 10 kΩ or higher |
| CV1 female connector 4 or KNK2 (C58-118) - Body ground | 10 kΩ or higher |
| CV1 female connector 3 or EKN2 (C58-117) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| CV1 female connector 2 or KNK1 (C55-95) - Body ground | 10 kΩ or higher |
| CV1 female connector 1 or EKNK (C55-94) - Body ground | 10 kΩ or higher |
| CV1 female connector 4 or KNK2 (C55-118) - Body ground | 10 kΩ or higher |
| CV1 female connector 3 or EKN2 (C55-117) - Body ground | 10 kΩ or higher |
Reconnect the CV1 connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.INSPECT ECM |
![]() |
Disconnect the CV1 connector.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| CV1 female connector 2 - 1 | 4.5 to 5.5 V |
| CV1 female connector 4 - 3 | 4.5 to 5.5 V |
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 4.INSPECT KNOCK SENSOR |
![]() |
Disconnect the CV1 connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| CV1 male connector 1 - 2 | 120 to 280 kΩ |
| CV1 male connector 3- 4 | 120 to 280 kΩ |
Reconnect the CV1 connector.
|
| ||||
| NG | |
| 5.CHECK HARNESS AND CONNECTOR (CONNECTOR - KNOCK SENSOR) |
![]() |
Disconnect the CV1 connector.
Disconnect the V2 and V1 knock sensor connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| CV1 male connector 2 - V2-2 | Below 1 Ω |
| CV1 male connector 1 - V2-1 | Below 1 Ω |
| CV1 male connector 4 - V1-2 | Below 1 Ω |
| CV1 male connector 3 - V1-1 | Below 1 Ω |
| Tester Connection | Specified Condition |
| CV1 male connector 2 or V2-2 - Body ground | 10 kΩ or higher |
| CV1 male connector 1 or V2-1 - Body ground | 10 kΩ or higher |
| CV1 male connector 4 or V1-2 - Body ground | 10 kΩ or higher |
| CV1 male connector 3 or V1-1 - Body ground | 10 kΩ or higher |
Reconnect the CV1 connector.
Reconnect the knock sensor connectors.
|
| ||||
| OK | ||
| ||