Home › ENGINE · 2AZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0617    Starter Relay Circuit High

for Preparation Click here


DESCRIPTION

While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.

DTC No.
DTC Detection Condition
Trouble Area
P0617
When conditions (a), (b) and (c) are met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20 seconds (1 trip detection logic)
  1. (a) Vehicle speed 20 km/h (12.4 mph) or more
  2. (b) Engine speed 1,000 rpm or more
  3. (c) STA signal ON
  1. Park/Neutral Position (PNP) switch (Automatic transaxle)
  2. Clutch start switch (Manual transaxle)
  3. Starter relay circuit
  4. Ignition switch
  5. ECM

WIRING DIAGRAM


A141372E01


INSPECTION PROCEDURE

HINT:
  1. The following troubleshooting flowchart is based on the premise that the engine is cranked normally.
    If the engine does not crank, proceed to the problem symptoms table (Click here).
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value displayed on the tester when the ignition switch is in the ON and START positions.

    OK:

    Ignition Switch Position
    STARTER SIG
    ON
    OFF
    START
    ON



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS 

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

HINT:
For vehicles with the manual transaxle, proceed to step 5.



    A107908E01
  1. Disconnect the C1 PNP switch connector.

  1. Measure the resistance when the transaxle gear selector lever is moved to each position.

    Standard resistance:
    Gear Selector
    Lever Position
    Tester Connection
    Specified Condition
    P
    2 - 6, 4 - 5
    Below 1 Ω
    R
    1 - 2
    Below 1 Ω
    N
    2 - 9, 4 - 5
    Below 1 Ω
    D
    2 - 7
    Below 1 Ω
    2
    2 - 3
    Below 1 Ω
    L
    2 - 8
    Below 1 Ω

  1. Reconnect the PNP switch connector.



OK
Go to step 8
NG


3.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NEXT


4.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value displayed on the tester when the ignition switch is in the ON and START positions.

    OK:

    Ignition Switch Positions
    STARTER SIG
    ON
    OFF
    START
    ON



NG
Go to step 8
OK

SYSTEM OK 

5.INSPECT CLUTCH START SWITCH ASSEMBLY


    A136164E01
  1. Disconnect the A22 clutch start switch connector.

  1. Measure the resistance between the terminals.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Clutch pedal released
    10 kΩ or higher
    1 - 2
    Clutch pedal depressed
    Below 1 Ω

  1. Reconnect the clutch start switch connector.



OK
Go to step 8
NG


6.REPLACE CLUTCH START SWITCH ASSEMBLY

NEXT


7.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value displayed on the tester when the ignition switch is in the ON and START positions.

    OK:

    Ignition Switch Position
    STARTER SIG
    ON
    OFF
    START
    ON



NG
Go to step 8
OK

SYSTEM OK 

8.INSPECT IGNITION SWITCH ASSEMBLY


    A056879E35
  1. Disconnect the E23 ignition switch connector.

  1. Measure the resistance between the terminals.

    Standard resistance:
    Tester Connection
    Ignition Switch Position
    Specified Condition
    All Terminals
    LOCK
    10 kΩ or higher
    2 - 4
    ACC
    Below 1 Ω
    1 - 2 - 4, 5 - 6
    ON
    1 - 3 - 4, 5 - 6 - 7
    START

  1. Reconnect the ignition switch connector.



OK
Go to step 10
NG


9.REPLACE IGNITION SWITCH ASSEMBLY

NEXT


10.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value displayed on the tester when the ignition switch is in the ON and START positions.

    OK:

    Ignition Switch Position
    STARTER SIG
    ON
    OFF
    START
    ON



NG
Go to step 11
OK

SYSTEM OK 

11.REPAIR OR REPLACE HARNESS OR CONNECTOR (PNP SWITCH OR CLUTCH START SWITCH - STA TERMINAL OF ECM)

NEXT


12.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Drive the vehicle at more than 20 km/h (12.43 mph) for over 20 seconds.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed To
    P0617
    A
    No DTC
    B



B
SYSTEM OK
A

REPLACE ECM