Home › TRANSMISSION · U660E AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P0617    Starter Relay Circuit High

for Preparation Click here


DESCRIPTION

While the engine is being cranked, the positive battery voltage is applied to terminal STA of the TCM.
If the TCM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The TCM then illuminates the MIL and sets the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.

DTC No.
DTC Detection Condition
Trouble Area
P0617
When conditions (a), (b) and (c) are met, positive (+B) battery voltage of 10.5 V or more is applied to TCM for 20 seconds
(1 trip detection logic):
(a) Vehicle speed more than 20 km/h (12.4 mph)
(b) Engine speed more than 1,000 rpm
(c) STA signal ON
  1. Park/neutral position switch
  2. Starter relay circuit
  3. Ignition switch
  4. TCM

WIRING DIAGRAM


C122810E01


INSPECTION PROCEDURE

HINT:
  1. The following troubleshooting flowchart is based on the premise that the engine is cranked normally. If the engine does not crank, proceed to the problem symptoms table (Click here).
  2. Read freeze frame data using the intelligent tester. The TCM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Enter the following menus: Powertrain / ECT / Data List.

  1. Check the value displayed on the tester when the ignition switch is turned to the ON position and the engine is started.

    OK:

    Engine Switch Condition
    ON (IG)
    ENGINE START
    Starter Signal
    OFF
    ON



OK
REPLACE TCM (Click here)
NG


2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    A107908E06
  1. Inspect the Park/Neutral Position (PNP) switch.

    1. Disconnect the C1 switch connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Gear Selector Lever Position
      Tester Connection
      Specified Condition
      P
      4 - 9
      Below 1 Ω
      N
      4 - 9
      Below 1 Ω

    3. Reconnect the PNP switch connector.



NG
REPLACE PARK/NEUTRAL POSITION SWITCH (Click here)
OK


3.INSPECT IGNITION SWITCH ASSEMBLY


    A135034E01
  1. Disconnect the E23 ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Switch Condition
    Tester Connection
    Specified Condition
    LOCK
    3-4, 5-7
    10 kΩ or higher
    START
    3-4, 5-7
    Below 1 Ω

  1. Reconnect the ignition switch connector.



NG
REPAIR OR REPLACE IGNITION SWITCH ASSEMBLY
OK


4.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Enter the following menus: Powertrain / ECT / Data List.

  1. Check the value displayed on the tester when the ignition switch is turned to the ON position and the engine is started.

    OK:

    Ignition Switch Condition
    ON (IG)
    ENGINE START
    Starter Signal
    OFF
    ON



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

SYSTEM IS OK