DTC P0617 Starter Relay Circuit High |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0617 | When conditions (a), (b) and (c) are met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20 seconds (1 trip detection logic)
|
|

| 1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the tester when the ignition switch is in the ON and START positions.
| Ignition Switch Position | STARTER SIG |
| ON | OFF |
| START | ON |
|
| ||||
| OK | ||
| ||
| 2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Disconnect the C1 PNP switch connector.
Measure the resistance when the transaxle gear selector lever is moved to each position.
| Gear Selector Lever Position | Tester Connection | Specified Condition |
| P | 2 - 6, 4 - 5 | Below 1 Ω |
| R | 1 - 2 | Below 1 Ω |
| N | 2 - 9, 4 - 5 | Below 1 Ω |
| D | 2 - 7 | Below 1 Ω |
| 2 | 2 - 3 | Below 1 Ω |
| L | 2 - 8 | Below 1 Ω |
Reconnect the PNP switch connector.
|
| ||||
| NG | |
| 3.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
| NEXT | |
| 4.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the tester when the ignition switch is in the ON and START positions.
| Ignition Switch Positions | STARTER SIG |
| ON | OFF |
| START | ON |
|
| ||||
| OK | ||
| ||
| 5.INSPECT CLUTCH START SWITCH ASSEMBLY |
![]() |
Disconnect the A22 clutch start switch connector.
Measure the resistance between the terminals.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - 2 | Clutch pedal released | 10 kΩ or higher |
| 1 - 2 | Clutch pedal depressed | Below 1 Ω |
Reconnect the clutch start switch connector.
|
| ||||
| NG | |
| 6.REPLACE CLUTCH START SWITCH ASSEMBLY |
| NEXT | |
| 7.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the tester when the ignition switch is in the ON and START positions.
| Ignition Switch Position | STARTER SIG |
| ON | OFF |
| START | ON |
|
| ||||
| OK | ||
| ||
| 8.INSPECT IGNITION SWITCH ASSEMBLY |
![]() |
Disconnect the E23 ignition switch connector.
Measure the resistance between the terminals.
| Tester Connection | Ignition Switch Position | Specified Condition |
| All Terminals | LOCK | 10 kΩ or higher |
| 2 - 4 | ACC | Below 1 Ω |
| 1 - 2 - 4, 5 - 6 | ON | |
| 1 - 3 - 4, 5 - 6 - 7 | START |
Reconnect the ignition switch connector.
|
| ||||
| NG | |
| 9.REPLACE IGNITION SWITCH ASSEMBLY |
| NEXT | |
| 10.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the tester when the ignition switch is in the ON and START positions.
| Ignition Switch Position | STARTER SIG |
| ON | OFF |
| START | ON |
|
| ||||
| OK | ||
| ||
| 11.REPAIR OR REPLACE HARNESS OR CONNECTOR (PNP SWITCH OR CLUTCH START SWITCH - STA TERMINAL OF ECM) |
| NEXT | |
| 12.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Clear the DTCs (Click here).
Drive the vehicle at more than 20 km/h (12.43 mph) for over 20 seconds.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed To |
| P0617 | A |
| No DTC | B |
|
| ||||
| A | ||
| ||