DTC P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) |
DTC P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) |
DTC P0138 Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0136 |
|
|
| P0137 |
|
|
| P0138 |
|
|




![]() |
| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS B1 S1 (A/F) | +25% | Rich | Less than 3.0 |
| -12.5% | Lean | More than 3.35 | |
| O2S B1 S2 (HO2) | +25% | Rich | More than 0.5 |
| -12.5% | Lean | Less than 0.4 |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area | ||
| 1 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() | - |
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage More than 0.5 V Less than 0.4 V | ![]() | ||
| 2 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage More than 0.5 V Less than 0.4 V | ![]() | ||
| 3 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 4 | Injection volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 1.READ OUTPUT DTC |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P0138 is output | A |
| P0137 is output | B |
| P0136 is output | C |
| P0136, P0137 or P0138 and other DTCs are output | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / O2S B1S2.
Allow the engine to idle.
Read the heated oxygen sensor output voltage while idling.
| Heated Oxygen Sensor Output Voltage | Proceed to |
| 1.0 V or higher | A |
| Below 1.0 V | B |
|
| ||||
| A | |
| 3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT) |
![]() |
Disconnect the heated oxygen sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| +B (2) - OX1B (3) | 10 kΩ or higher |
| +B (2) - E2 (4) | 10 kΩ or higher |
Reconnect the heated oxygen sensor connector.
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
![]() |
Turn the ignition switch off and wait for 5 minutes.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| HT1B (C24-47) - OX1B (C24-64) | 10 kΩ or higher |
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
Change the fuel injection volume using the tester and monitor the voltage output of the air fuel ratio and heated oxygen sensors displayed on the tester.
| Tester Display (Sensor) | Voltage Variation | Proceed to |
| AFS Voltage B1S1 | Alternates between higher than and below 3.3 V | OK |
| Remains at higher than 3.3 V | NG | |
| Remains at below 3.3 V | NG |

|
| ||||
| OK | |
| 6.INSPECT AIR FUEL RATIO SENSOR |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Clear DTCs.
Drive the vehicle according to the drive pattern listed below.
Warm up the engine.
Drive the vehicle at 60 km/h (40 mph) or more for 10 minutes or more.
Stop the vehicle.
Accelerate the vehicle to 60 km/h (40 mph) or more and decelerate for 7 seconds or more. Perform this 3 times.

Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / AFS Current B1S1.
Read the value of the air fuel ratio sensor current while the fuel-cut operation is being performed.
|
| ||||
|
| ||||
| 7.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / All Data / O2S B1S2.
Change the fuel injection volume using the tester, monitoring the voltage output of the heated oxygen sensors displayed on the tester.
|
| ||||
| OK | |
| 8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
Change the fuel injection volume using the tester and monitor the voltage output of the air fuel ratio and heated oxygen sensors displayed on the tester.
| Tester Display (Sensor) | Voltage Variation | Proceed to |
| AFS Voltage B1S1 | Alternates between higher than and below 3.3 V | OK |
| Remains at higher than 3.3 V | NG | |
| Remains at below 3.3 V | NG |

|
| ||||
| OK | ||
| ||
| 9.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leakage.
|
| ||||
| OK | |
| 10.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the C22 Heated Oxygen (HO2) sensor connector.
Measure the resistance between the terminals of the HO2 sensor connector.
| Tester Connection | Specified Condition |
| HT1B (1) - +B (2) | 11 to 16 Ω at 20°C (68°F) |
| HT1B (1) - E2 (4) | 10 kΩ or higher |
Reconnect the HO2 sensor connector.
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
![]() |
Disconnect the heated oxygen sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| HT1B (C22-1) - HT1B (C24-47) | Below 1 Ω |
| OX1B (C22-3) - OX1B (C24-64) | Below 1 Ω |
| E2 (C22-4) - EX1B (C24-87) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HT1B (C22-1) or HT1B (C24-47) - Body ground | 10 kΩ or higher |
| OX1B (C22-3) or OX1B (C24-64) - Body ground | 10 kΩ or higher |
| E2 (C22-4) or EX1B (C24-87) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 12.REPLACE HEATED OXYGEN SENSOR |
Replace the heated oxygen sensor.
| NEXT | |
| 13.PERFORM CONFIRMATION DRIVING PATTERN |
Perform Confirmation Driving Pattern.
| NEXT | |
| 14.CHECK WHETHER DTC OUTPUT RECURS (DTC 0136, P0137 OR P0138) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P0136, P0137 or P0138 is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||
| 15.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor.
| NEXT | |
| 16.PERFORM CONFIRMATION DRIVING PATTERN |
Perform Confirmation Driving Pattern.
| NEXT | |
| 17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 OR P0138) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P0136 or P0138 is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||