DTC P0100 Mass or Volume Air Flow Circuit |
DTC P0102 Mass or Volume Air Flow Circuit Low Input |
DTC P0103 Mass or Volume Air Flow Circuit High Input |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0100 | MAF meter voltage less than 0.2 V, or more than 4.9 V for 3 seconds (1 trip detection logic) |
|
| P0102 | MAF meter voltage less than 0.2 V for 3 seconds (1 trip detection logic) |
|
| P0103 | MAF meter voltage more than 4.9 V for 3 seconds (1 trip detection logic) |
|
| Mass Air Flow Rate (g/sec.) | Malfunction |
| Approximately 0.0 |
|
| 271.0 or more |
|

| 1.READ VALUE USING INTELLIGENT TESTER (MASS AIR FLOW RATE) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / MAF.
Read the values displayed on the tester.
| Mass Air Flow Rate (g/sec.) | Proceed to |
| 0.0 | A |
| 271.0 or more | B |
| Between 1.0 and 270.0 (*1) | C |
|
| ||||
|
| ||||
| A | |
| 2.INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE) |
![]() |
Disconnect the C2 Mass Air Flow (MAF) meter connector.
Turn the ignition switch to the ON position.
Measure the voltage between the terminal of the wire harness side connector and body ground.
| Tester Connection | Specified Condition |
| +B (C2-3) - Body ground | 9 to 14 V |
Reconnect the MAF meter connector.
|
| ||||
| OK | |
| 3.INSPECT MASS AIR FLOW METER (VG VOLTAGE) |
![]() |
Inspect output voltage.
Disconnect the C2 MAF meter connector.
Apply battery voltage across terminals +B and E2G.
Connect the positive (+) tester probe to terminal VG, and the negative (-) tester probe to terminal E2G.
Measure the voltage.
| Tester Connection | Specified Condition |
| VG (5) - E2G (4) | 0.2 to 4.9 V |
Reconnect the MAF meter connector.
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
![]() |
Disconnect the C2 MAF meter connector.
Disconnect the C24 ECM connector.
Measure the resistance between the terminals of the wire harness side connectors.
| Tester Connection | Specified Condition |
| VG (C2-5) - VG (C24-118) | Below 1 Ω |
| E2G (C2-4) - E2G (C24-116) |
| Tester Connection | Specified Condition |
| VG (C2-5) or VG (C24-118) - Body ground | 10 kΩ or higher |
Reconnect the MAF meter connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 5.INSPECT ENGINE ROOM J/B (EFI RELAY, EFI MAIN FUSE) |
![]() |
Inspect the EFI MAIN fuse.
Remove the EFI MAIN fuse from the engine room J/B.
Measure the EFI MAIN fuse resistance.
Reinstall the EFI MAIN fuse.
Inspect the EFI relay.
Remove the engine room J/B from the engine room R/B.
Measure the EFI relay resistance.
| Tester Connection | Specified Condition |
| 1E-6 - 1E-12 | 10 kΩ or higher |
| Below 1 Ω (Apply battery voltage between terminals 1E-9 and 1E-11) |
Reinstall the engine room J/B.
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ENGINE ROOM J/B) |
![]() |
Inspect the EFI No. 3 fuse.
Remove the EFI No. 3 fuse from the engine room R/B.
Measure the EFI No. 3 fuse resistance.
Reinstall the EFI No. 3 fuse.
Disconnect the C2 MAF meter connector.
Remove the engine room J/B from the engine room R/B.
Disconnect the 1E engine room J/B connector.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| +B (C2-3) - Engine room J/B (1E-6) | Below 1 Ω |
| Tester Connection | Specified Condition |
| +B (C2-3) or Engine room J/B (1E-6) - Body ground | 10 kΩ or higher |
Reconnect the MAF meter connector.
Reconnect the engine room J/B connector.
Reinstall the engine room J/B.
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (SENSOR GROUND) |
![]() |
Disconnect the C2 MAF meter connector.
Measure the resistance.
| Tester Connection | Specified Condition |
| E2G (C2-4) - Body ground | Below 1 Ω |
Reconnect the MAF meter connector.
|
| ||||
| NG | |
| 8.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
![]() |
Disconnect the C2 MAF meter connector.
Disconnect the C24 ECM connector.
Measure the resistance between the terminals of the wire harness side connectors.
| Tester Connection | Specified Condition |
| VG (C2-5) - VG (C24-118) | Below 1 Ω |
| E2G (C2-4) - E2G (C24-116) |
| Tester Connection | Specified Condition |
| VG (C2-5) or VG (C24-118) - Body ground | 10 kΩ or higher |
Reconnect the MAF meter connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||