DTC P0100 Mass or Volume Air Flow Circuit |
DTC P0102 Mass or Volume Air Flow Circuit Low Input |
DTC P0103 Mass or Volume Air Flow Circuit High Input |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0100 | Open or short in Mass Air Flow (MAF) meter circuit for 3 seconds |
|
| P0102 | Open in Mass Air Flow (MAF) meter circuit for 3 seconds |
|
| P0103 | Short in Mass Air Flow (MAF) meter circuit for 3 seconds |
|
| Mass Air Flow Rate (gm/s) | Malfunctions |
| Approximately 0.0 |
|
| 271.0 or more | Open in EVG circuit |

| 1.READ VALUE USING MASS AIR FLOW METER (MAF) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / MAF.
Read the values displayed on the tester.
| Mass Air Flow Rate (gm/s) | Proceed to |
| 0.0 | A |
| 271.0 or more | B |
| Between 1.0 and 270.0 (*1) | C |
|
| ||||
|
| ||||
| A | |
| 2.INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE) |
![]() |
Disconnect the C2 mass air flow (MAF) meter connector.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| +B (C2-3) - Body ground | 9 to 14 V |
Reconnect the MAF meter connector.
|
| ||||
| OK | |
| 3.INSPECT MASS AIR FLOW METER (VG VOLTAGE) |
![]() |
Inspect the output voltage.
Apply battery voltage across terminals +B and E2G.
Connect the positive (+) tester probe to terminal VG, and negative (-) tester probe to terminal E2G.
Measure the voltage between the terminals.
| Tester Connection | Specified Condition |
| 5 (VG) - 4 (E2G) | 0.2 to 4.9 V |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
![]() |
Disconnect the C2 MAF meter connector.
Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| VG (C58-72) - VG (C2-5) | Below 1 Ω |
| E2G (C58-73) - E2G (C2-4) | Below 1 Ω |
| Tester Connection | Specified Condition |
| VG (C55-72) - VG (C2-5) | Below 1 Ω |
| E2G (C55-73) - E2G (C2-4) | Below 1 Ω |
| Tester Connection | Specified Condition |
| VG (C58-72) or VG (C2-5) - Body ground | 10 kΩ or higher |
| E2G (C58-73) or E2G (C2-4) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| VG (C55-72) or VG (C2-5) - Body ground | 10 kΩ or higher |
| E2G (C55-73) or E2G (C2-4) - Body ground | 10 kΩ or higher |
Reconnect the MAF meter connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 5.INSPECT FUSE (EFI NO. 3) |
![]() |
Remove the EFI No. 3 fuse from the engine room R/B.
Measure the EFI No. 3 fuse resistance.
Reinstall the EFI No. 3 fuse.
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ENGINE ROOM JUNCTION BLOCK) |
![]() |
Disconnect the C2 MAF meter connector.
Remove the engine room junction block from the engine room R/B.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| +B (C2-3) - 1E-6 (Engine room R/B) | Below 1 Ω |
| Tester Connection | Specified Condition |
| +B (C2-3) or 1E-6 (Engine room R/B) - Body ground | 10 kΩ or higher |
Reinstall the engine room junction block.
Reconnect the C2 MAF meter connector.
|
| ||||
| OK | |
| 7.INSPECT ENGINE ROOM JUNCTION BLOCK (EFI RELAY) |
![]() |
Remove the engine room junction block from the engine room R/B.
Inspect the EFI relay.
Measure the EFI relay resistance.
| Tester Connection | Specified Condition |
| 1E-12 - 1E-6 | 10 kΩ or higher |
| 1E-12 - 1E-6 | Bellow 1 Ω (Apply battery voltage between terminals 1E-9 and 1E-10) |
Reinstall the engine room junction block.
|
| ||||
| OK | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (SENSOR GROUND) |
![]() |
Disconnect the C2 MAF meter connector.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| E2G (C2-4) - Body ground | Below 1 Ω |
Reconnect the MAF meter connector.
|
| ||||
| NG | |
| 9.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
![]() |
Disconnect the C2 MAF meter connector.
Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| VG (C58-72) - VG (C2-5) | Below 1 Ω |
| E2G (C58-73) - E2G (C2-4) | Below 1 Ω |
| Tester Connection | Specified Condition |
| VG (C55-72) - VG (C2-5) | Below 1 Ω |
| E2G (C55-73) - E2G (C2-4) | Below 1 Ω |
| Tester Connection | Specified Condition |
| VG (C58-72) or VG (C2-5) - Body ground | 10 kΩ or higher |
| E2G (C58-73) or E2G (C2-4) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| VG (C55-72) or VG (C2-5) - Body ground | 10 kΩ or higher |
| E2G (C55-73) or E2G (C2-4) - Body ground | 10 kΩ or higher |
Reconnect the MAF meter connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||