CENTER AIRBAG SENSOR ASSEMBLY > INSTALLATION |
| 1. INSTALL CENTER AIRBAG SENSOR ASSEMBLY |
Check that the ignition switch is off.
Check that the battery negative (-) cable is disconnected.
![]() |
Install the center airbag sensor assembly with the 3 bolts.
Check that there is no looseness in the installation parts of the center airbag sensor assembly.
Connect the holder (with connectors).
Check that the water-proof sheet is properly set.
| 2. INSTALL NO. 1 CONSOLE BOX DUCT (w/ Rear Register Duct) |
![]() |
Install the No. 1 console box duct with the clip.
| 3. INSTALL NO. 2 CONSOLE BOX INSERT FRONT |
![]() |
Engage the clip.
Install the No. 2 console box insert front with the 3 screws <F>.
| 4. INSTALL NO. 1 CONSOLE BOX INSERT FRONT |
![]() |
Engage the clip.
Install the No. 1 console box insert front with the 3 screws <F>.
| 5. INSTALL CONSOLE BOX ASSEMBLY |
![]() |
Install the 2 screws <F>.
![]() |
Install the console box assembly with the 2 bolts <G>.
| 6. INSTALL CONSOLE BOX CARPET |
![]() |
Install the console box carpet.
| 7. INSTALL CONSOLE BOX POCKET |
Install the console box pocket.
| 8. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Engage the 3 claws and 3 clips.
Install the 4 screws <B>.
Install the lower instrument panel sub-assembly with the bolt <A>.
| 9. INSTALL INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY |
![]() |
Engage the 4 claws and 2 guides and install the instrument panel No. 2 under cover.
| 10. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH |
| 11. INSTALL FRONT DOOR SCUFF PLATE RH |
| 12. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH |
![]() |
Install the air hose and connect the connector.
Engage the 2 claws and the DLC3.
Engage the claw and the 4 clips.
Instal the lower instrument panel finish panel LH with the screw <B> and bolt <A>.
| 13. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Engage the 2 clips.
Install the cowl side trim sub-assembly LH with the cowl side trim clip.
| 14. INSTALL FRONT DOOR SCUFF PLATE LH |
![]() |
Engage the 7 claws and 3 clips, then install the front door scuff plate LH.
| 15. INSTALL LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY |
Connect each connector.
![]() |
Engage the 2 claws and 2 clips.
Install the lower instrument cluster finish panel center sub-assembly with the 2 screws <F>.
| 16. INSTALL UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Engage the 3 claws and 5 clips to install the upper console rear panel sub-assembly.
| 17. INSTALL UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle) |
![]() |
Connect the connector and engage the clamp.
Engage the 3 claws and 5 clips to install the upper console rear panel sub-assembly.
| 18. INSTALL UPPER CONSOLE PANEL (for Manual Transaxle) |
![]() |
Engage the 2 claws and the 5 clips to install the upper console panel as shown in the illustration.
| 19. INSTALL FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY (for Automatic Transaxle) |
with Seat Heater System:
Connect each connector.
![]() |
Engage the 6 claws and the 3 clips to install the floor shift position indicator housing sub-assembly.
| 20. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
![]() |
Engage the 2 clips and install the No. 2 instrument cluster finish panel garnish.
| 21. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
![]() |
Engage the 2 clips and install the No. 1 instrument cluster finish panel garnish.
| 22. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Install the shift lever knob sub-assembly.
| 23. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle) |
![]() |
Install the shift lever knob sub-assembly.
| 24. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 25. INSPECT SRS WARNING LIGHT |
Inspect the SRS warning light (Click here).