CENTER AIRBAG SENSOR ASSEMBLY > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle) |
![]() |
Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.
| 4. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.
| 5. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
![]() |
Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.
| 6. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH |
![]() |
Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.
| 7. REMOVE FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY (for Automatic Transaxle) |
![]() |
Disengage the 6 claws and the 3 clips, and then remove the floor shift position indicator housing sub-assembly.
with Seat Heater System:
Disconnect each connector.
| 8. REMOVE UPPER CONSOLE PANEL (for Manual Transaxle) |
![]() |
Open the lid of the upper console panel.
Apply protective tape to the area shown in the illustration.
![]() |
Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the upper console panel as shown in the illustration.
| 9. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle) |
![]() |
Disengage the 3 claws and the 5 clips.
Disengage the clamp.
Disconnect the connector and remove the upper console rear panel sub-assembly.
| 10. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.
| 11. REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY |
![]() |
Remove the 2 screws <F>.
Disengage the 4 claws.
Disconnect each connector and remove the instrument cluster finish panel center sub-assembly.
| 12. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() |
Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.
| 13. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Remove the cowl side trim clip.
Disengage the 2 clips and remove the cowl side trim sub-assembly LH.
| 14. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL LH |
![]() |
Remove the bolt <A> and the screw <B>.
Disengage the 2 claws and the DLC3.
Disconnect the hood lock control cable assembly.
Disengage the claw and the 4 clips.
Remove the air hose, disconnect the connector, and then remove the lower instrument panel finish panel LH.
| 15. REMOVE FRONT DOOR SCUFF PLATE RH |
| 16. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH |
| 17. REMOVE INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY |
![]() |
Disengage the 4 claws.
Disengage the 2 guides and remove the No. 2 under cover sub-assembly.
| 18. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
Remove the bolt <A>.
![]() |
Remove the 4 screws <B>.
Disengage the 3 claws and 3 clips, and then remove the lower instrument panel sub-assembly.
| 19. REMOVE CONSOLE BOX POCKET |
Remove the console box pocket.
| 20. REMOVE CONSOLE BOX CARPET |
![]() |
Remove the console box carpet.
| 21. REMOVE CONSOLE BOX ASSEMBLY |
![]() |
Remove the 2 screws <F>.
![]() |
Remove the 2 bolts <G> and the console box assembly.
| 22. REMOVE NO. 1 CONSOLE BOX INSERT FRONT |
![]() |
Remove the 3 screws <F>.
Disengage the clip and remove the No. 1 console box insert front.
| 23. REMOVE NO. 2 CONSOLE BOX INSERT FRONT |
![]() |
Remove the 3 screws <F>.
Disengage the clip and remove the No. 2 console box insert front.
| 24. REMOVE NO. 1 CONSOLE BOX DUCT (w/ Rear Register Duct) |
![]() |
Remove the clip and No. 1 console box duct.
| 25. REMOVE CENTER AIRBAG SENSOR ASSEMBLY |
Turn back the carpet.
![]() |
Disconnect the holder (with connectors).
Remove the 3 bolts and center airbag sensor assembly.