Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › CENTER AIRBAG SENSOR ASSEMBLY

CENTER AIRBAG SENSOR ASSEMBLY > REMOVAL

for Preparation Click here



1. PRECAUTION

CAUTION:
Be sure to read "PRECAUTION" thoroughly before servicing (Click here).

NOTICE:
w/ Navigation System for HDD:
After the ignition switch is turned off, the navigation receiver assembly (HDD navigation system) records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.



3. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle)


    B226062
  1. Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.



4. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)


    B137272
  1. Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.



5. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B226063
  1. Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.



6. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B226064
  1. Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.



7. REMOVE FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY (for Automatic Transaxle)


    B226065
  1. Disengage the 6 claws and the 3 clips, and then remove the floor shift position indicator housing sub-assembly.

  1. with Seat Heater System:

    1. Disconnect each connector.



8. REMOVE UPPER CONSOLE PANEL (for Manual Transaxle)


    B137274E01
  1. Open the lid of the upper console panel.

  1. Apply protective tape to the area shown in the illustration.



    B137275
  1. Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the upper console panel as shown in the illustration.

  1. with Seat Heater System:

    1. Disconnect each connector.



9. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle)


    B226097
  1. Disengage the 3 claws and the 5 clips.

  1. Disconnect the connector and remove the upper console rear panel sub-assembly.



10. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Manual Transaxle)


    B137277
  1. Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.



11. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    B133997E01
  1. Remove the 2 screws <F>.

  1. Disengage the 4 claws.

  1. Disconnect each connector and remove the upper console panel sub-assembly.

    HINT:
    Set the shift lever in the D position.



12. REMOVE FRONT DOOR SCUFF PLATE LH


    B132067
  1. Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.



13. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    B132116E01
  1. Remove the cowl side trim clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.



14. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL LH


    B147263E01
  1. Remove the bolt <A> and the screw <B>.

  1. Disengage the 2 claws and the DLC3.

  1. Disconnect the hood lock control cable assembly.

  1. Disengage the claw and the 4 clips.

  1. Remove the air hose, disconnect the connector, and then remove the lower instrument panel finish panel LH.



15. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures for the RH side and the LH side.



16. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedures for the RH side and the LH side.



17. REMOVE INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY


    B133988E01
  1. Disengage the 4 claws.

  1. Disengage the 2 guides and remove the No. 2 under cover sub-assembly.



18. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
  1. Remove the bolt <A>.



    B133992E01
  1. Remove the 4 screws <B>.

  1. Disengage the 3 claws and 3 clips, and then remove the lower instrument panel sub-assembly.



19. REMOVE CONSOLE BOX POCKET
  1. Remove the console box pocket.



20. REMOVE CONSOLE BOX CARPET


    B134004
  1. Remove the console box carpet.



21. REMOVE CONSOLE BOX ASSEMBLY


    B134002E01
  1. Remove the 2 screws <F>.



    B134003E01
  1. Remove the 2 bolts <G> and the console box assembly.



22. REMOVE NO. 1 CONSOLE BOX INSERT FRONT


    B134006E01
  1. Remove the 3 screws <F>.

  1. Disengage the clip and remove the No. 1 console box insert front.



23. REMOVE NO. 2 CONSOLE BOX INSERT FRONT


    B134005E01
  1. Remove the 3 screws <F>.

  1. Disengage the clip and remove the No. 2 console box insert front.



24. REMOVE NO. 1 CONSOLE BOX DUCT (w/ Rear Register Duct)


    C129716
  1. Remove the clip and No. 1 console box duct.



25. REMOVE CENTER AIRBAG SENSOR ASSEMBLY
  1. Turn back the carpet.



    C133884
  1. Disconnect the holder (with connectors).

  1. Remove the 3 bolts and center airbag sensor assembly.